BC250 Tower Case ( Xbox series X / Ch270 Inspired) - ATX PSU / AIO
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Vertical console-style tower for the AMD BC-250 board with an Arctic Liquid Freezer III 280 AIO and a full-size ATX PSU.
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 13
- Wydruki
- 0
- Wyświetlenia
- 856
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
⚠ Status: design-complete prototype, not yet fully printed. The geometry has been validated with PLA test pieces (tube-bend jig, PSU screw pattern, joint samples) but the full case has not been printed and assembled yet. I'm publishing it at this stage to get feedback from the community on the design choices before committing ~2.7 kg of ABS. If you print it, you're an early tester — comments very welcome.
What it is
A fully 3D-printed vertical tower (console-style, Series-X-ish proportions) that turns an AMD BC-250 — the PS5-derived mining board — into a quiet living-room machine:
Arctic Liquid Freezer III 280 AIO on the board's APU: the board stands vertically, and the radiator + both 140 mm fans stand vertically too, as a full-height wall behind an internal partition on one flank — one flank of the tower is the intake, the radiator flank is the exhaust
Full-size ATX PSU standing on its end in the base — the tower literally stands on the PSU bay
Footprint only 160 × 234 mm, height ≈ 445 mm
No visible cables: the IEC inlet hides in the plinth (slot at the rear), the board I/O sits under a rear-open hood on top, and a pill-shaped slot high on the front docks a slim USB hub (Anker Ultra Slim, 100×30×10 mm) that rests on the internal head plate, its cable running to the board's USB inside the hood
Dense hexagonal mesh (~9.2 mm cells, 2.5 mm webs, 1828 openings) on the front, both flanks, rear and roof — about 43% open area
Power button hole (Ø16.2 mm for a standard 16 mm vandal switch) on the upper front, aligned to the hex grid
The two printed parts
The case splits into two "cups" that slide together on a lipped joint (0.2 mm clearance) secured by six M3 screws into Ø3.4 pilot bosses:
Part | Print height | Est. weight (ABS, 0.12 mm) | Est. time |
|---|---|---|---|
bicchiere_basso (lower cup, PSU + board bay) | 210 mm | ~637 g (incl. 146 g supports) | ~2 d 1 h |
bicchiere_alto (upper cup, radiator + hood) | 235.5 mm | ~719 g (incl. 188 g supports) | ~2 d 13 h |
Times are from OrcaSlicer at 0.12 mm / 3 walls / 20% infill on a Qidi Q1 Pro — a coarser profile will cut them drastically.
Print orientation (important!)
Lower cup: plinth face on the bed (open joint up)
Upper cup: UPSIDE DOWN — hood face on the bed. Printed the "natural" way up, the internal head plate generates ~1 kg of support towers; flipped, supports drop to ~190 g.
Enclosed printer strongly recommended for ABS at this size (designed on a 245×245×240 machine — the upper cup uses 235.5 mm of Z).
The hex cells sit on ~4.6 mm internal bridges on the horizontal diaphragms; they print fine slowly in an enclosure, but expect slightly rough cells with fast open-air PLA.
Hardware you need (BOM)
AMD BC-250 board
Arctic Liquid Freezer III 280 (tubes exit toward the head plate; the routing is designed around the real 30 mm bend radius and the 24 mm port spacing — a printable tube-bend jig is included so you can check your unit first)
ATX PSU (standard mounting pattern; mounts on 4 slotted holes, IEC facing the plinth slot)
PS_ON bridge/adapter for the BC-250 (e.g. the mosfet.party board) — a dedicated bay in the plinth is still being designed
16 mm vandal-style power button (Ø16.2 hole)
6× M3 screws + heat-set inserts for the cup joint
8× fan screws for the intake side (Ø4.3 holes, 105 mm pitch)
Display cables with 90° connectors (DP/HDMI) — straight connectors don't fit under the cable hood (~42 mm clearance)
Optional: Anker Ultra Slim 4-port USB hub (the front slot is sized for it, cable ≥60 cm version)
Included files
bicchiere_basso.stl,bicchiere_alto.stl— the case it self, it's a veeeery long print.
These are test printsprov_dima_tubo.stl— tube-bend jig (R30): print this first and check it against your AIO's tubesprov_piastra_psu.stl— PSU pattern / IEC-switch aperture test plateprov_giunto_maschio.stl/prov_giunto_femmina.stl— a small section of the cup joint to verify fit and the M3 bossprov_fronte_hub.stl— front section with the button hole and hub slot
Known open points (feedback wanted!)
Thermals are unproven: the VRAM on the back of the board is the critical spot. The mesh is ~43% open; intake is the flanks, exhaust through the radiator up top.
The PS_ON adapter bay in the plinth is not modeled yet (waiting for board dimensions).
No dust filter frame yet on the intake flank — planned as an add-on.
0.12 mm layers everywhere is probably overkill; if you try 0.16/0.2 tell me how the joint fits.
Printer settings I use
Qidi Q1 Pro, generic ABS, 0.12 mm layers, 3 perimeters, 20% infill, normal (auto) supports, brim. Bed 100 °C, chamber closed.
