Miracle Dice Box - Rearrange 6 dice inside of a closed box with the snap of a finger or tap of a magic wand! MMU not required!
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This magic box takes six normal dice ordered from 1 to 6, rearranges them to all match, and then back into order!
- Ocena
- 0 / 5
- Polubienia
- 8
- Pobrania
- 11
- Wydruki
- 0
- Wyświetlenia
- 323
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Puzzles & Brain-teasers
- Licencja
- Creative Commons — Attribution — Noncommercial
The Magic Dice Box
This is an 3D printable version of the classic "Miracle Dice Box" or "Problema Dice", originally produced in the 1950s by a German Magician Martin Paufler.
Six dice are placed in a box numbered in order, 1 through 6. The box is then closed and another die is rolled on top of the box. After a simple snap, or tap from a magic wand, the box can be opened to reveal that all the dice inside have been re-arranged to match the rolled die, as if by magic.
After removing the die, another tap from a magic wand will rearrange all the dice back to their original ordered state!
Non-Printed Bill Of Materials:
QTY 4 6mm OD x 2mm Thick Magnets. Amazon Link (non-affiliate)
Super Glue, or other adhesive suitable for bonding 3D printed plastic
Dark permanent marker to match the dice (not required, but helps with the illusion in bright light)
Printing Considerations:
Matching filaments are recommended for the box and dice to help with the illusion, although they are not required.
The 6 dice for inside the box are of standard dimensions, and could be replaced with any actual dice if you want, as long as you have a filament or paint that matches them.
Print with a minimum resolution of 0.2mm layers, 0.4mm nozzle
A textured plate may help the illusion.
Sanding the mating faces of the Magic Die before assembly may help with the illusion
Magic_Dice_Box_False_Dice_Bottom prints best in the orientation provided, BUT the illusion is improved if it is flipped over so that its surface finish matches that of the inside of the lid. I recommend printing it both ways and seeing what works best for you.
MMU is NOT required. The dice cutouts are indented, so they can be painted in with nail polish, or colored in with a marker.
Multiple Magic Dice can be printed to keep the trick fresh and entertaining.
The Trick:
Show your audience the box with all the dice arranged 1 through 6

Close the box
Roll the Magic Die using the Dice Cup and land the magic die on top of the box
This does take a bit of practice. You will feel when the magic is performed and develop a sense of how to effectively roll the Magic Die quickly
Using the Dice Cup is optional, but I think it helps with the illusion!
Snap your finger or tap the box with a magical object

Open the box and show your audience that the dice inside the box have been magically re-arranged to match the shown value on the rolled die. (Hold the lid level or pinch the Magic Die in place with your finger for maximum effect and not to give anything away)
You can dump all the dice on the table at this point for added effect.

Replace the lid and remove the Magic Die. Then, snap or tap the box again
Open the box to show that the dice have been magically re-arranged to be in their original order!
Assembly:
ASSEMBLY NOTICE: It is IMPERATIVE that the magnets are glued in the correct orientation. Stop and make sure that you have the poles oriented correctly before gluing.
Glue 3 magnets into the False Dice Plate
Consider coloring both sides of the magnets with a dark permanent marker. The top plate is very thin where the magnets are, and coloring them dark hides their reflective surface
MAKE SURE ALL THREE MAGNETS ARE POLARIZED IN THE SAME DIRECTION.

Glue the backer to the False Dice Plate

Glue a magnet into the hole on the Magic Die
MAKE SURE TO ORIENT THE MAGNET SO THAT IT WILL BE ATTRACTED TO THE 3 MAGNETS GLUED IN PREVIOUS STEP WHEN THE DIE IS ASSEMBLED, OR THE TRICK WILL NOT WORK

Glue the halves of the Magic Die together