Frost Crystal Casket — makeup organizer, no supports
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A glacier block with a bored quartz cluster. Brushes stand bristles-up. No blind holes, no supports.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 3
- Wydruki
- 0
- Wyświetlenia
- 43
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Bathroom
- Licencja
- Creative Commons — Attribution
Frost Crystal Casket
A block of glacier ice with a quartz cluster growing out of the back — and the cluster is the working part.

3 parts · 132 × 114 × 100 mm assembled · 298 g · no supports, no hardware, no glue, no paint. Assembly is dropping two plates into a rebate.
Every crystal is bored straight through
Push a brush into a shard and it stands bristles-up while its handle hangs in the box underneath. Because the four brush bores are one diameter all the way through rather than a pocket with a floor, the handle drops until the brush hangs on its own taper — which is what makes a 120 mm brush and a 220 mm brush stand at the same height.

The bores are cut to measured stock, not guessed:
Big crystal, bore Ø27 ......... mascara (stock 20-26 mm) Two crystals, bore Ø23 ........ lipstick (stock 19-22 mm) Two crystals, bore Ø16 ........ fat brush handles (10-14 mm) Two crystals, bore Ø11 ........ slim brush handles (8-11 mm) Four comb bays, 22.6 mm ....... lipstick, pencils, liners, jars
The three tube bores neck down to Ø14 through the plate instead of bottoming out, so a lipstick rests on the shoulder rather than falling into the well — and the hole is still far wider than a cotton bud.
There is not one blind hole in it
That is a structural answer to the thing that kills makeup organizers, not a claim in the copy. Every crystal bore goes through the plate into the well underneath, so a bud goes in from either end. The two inserts lift straight out. And the well they sit over is a single cavity with a 4 mm cove where the floor meets the wall, so there is no square internal corner anywhere for loose powder to pack into.
To clean it: lift both inserts out, tip the well over a bin, one wipe.

The three parts
body.stl 1x 132 x 114 x 38 mm 134 g the ice block cluster.stl 1x 122 x 69 x 66 mm 156 g 7 bored crystals + 12 spires comb.stl 1x 118 x 32 x 4 mm 8 g 4-bay slotted plate

body — one coved well, 38 mm deep, with a 4 mm rebate round the rim that both inserts drop into flush.
cluster — 7 bored crystals and 12 solid spires on a 4 mm plate, covering the back of the well. This is the brush and tube rack.
comb — a slotted plate over the front of the well: four 22.6 mm bays for lipsticks, pencils and small jars, which stand on the box floor.
Printing
Every part prints in the pose the STL is saved in, flat on the bed, no supports and no flips. 0.2 mm layers, 3 walls, 15 % infill. ~298 g of PLA and nothing else.
A translucent, pearl or plain white filament is the one that sells the ice — the photos here are a blue-to-white gradient PLA. It is a single colour throughout; there is no second-colour band to set up.
The crystals lean apart, not together. That is deliberate: the first layout leaned them toward each other and closed a wedge between the two ranks that sealed as trapped air pockets. Fanning them outward opens every gap to the sky. The worst lean is 17° off vertical, so the steepest underside is still 73° from horizontal — nothing here needs support.

Assembly
Drop the cluster into the back of the rim rebate. It seats on 2.0 mm of ledge on three sides; 0.35 mm of clearance per side means it drops rather than presses.
Drop the comb into the front of the same rebate.
The 0.8 mm gap between the two inserts is on purpose — that is the finger slot you lift either one out by.

Parametric
The OpenSCAD source ships with it. Bore diameters, the well depth, the crystal count and the rebate clearance are all named variables at the top of the file, so the rack can be re-cut to whatever is actually in your drawer.
