Portable/Secondary Monitor
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A design for a portable/miniature monitor based around a 16:9 IPS 1080P laptop display I had from an old ThinkPad E480.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 82
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Open Community License v1.1 + General Attribution v1
A design for a portable/miniature monitor based around a 16:9 IPS 1080P laptop display I had from an old ThinkPad E480. It has stereo speakers, a USB-A port to connect one additional device, a 3.5 mm audio port, a mini HDMI input, and a USB-C DisplayPort input. It uses an additional USB-C port for power. It has a VESA MIS-B mounting pattern on the back so you should be able to use it with any compatible VESA equipment or the provided stand.
Print Instructions:
Print all parts in PETG with at least 4 walls and 15% cubic infill. No supports are needed for any part as they take advantage of bridging techniques though the large flat rear parts of the monitor may need a 5 mm brim to prevent warping. The parts are split down the middle with a somewhat aesthetic seam so you don't need to assemble anything with dowel pins and can still print the entire thing on a Prusa i3 buildplate. Print one of every part except the spacers which you will need four of. You may want some superglue during assembly though if you find that some of your parts are warped & don't stay seamless. I used just a couple drops to make the thin front frame a bit more rigidly formed together. You may also want to use some superglue on the spacers for the VESA mount during assembly to prevent them from coming loose.
You will need the following parts:
1 - 16:9 14" display panel (salvaged from a ThinkPad E480 or any other model that uses the same panel, Panel Info, this panel should work if you need to purchase one)
1 - USB-A female port salvaged from an extension cable like this
1 - Pair of 2030 2W cavity speakers like this set from Waveshare
1 - 4-pin JST-PH connector with crimped cable (you can crimp this yourself if you have the connector, cable, & a crimp tool or you can get something like this and solder it to the salvaged USB-A port's wires)
1 - Universal 40-pin EDP display driver board capable of driving at least 1080P resolution (this is the model I chose which my design is made for in terms of port spacing & mounting holes)
4 - M2x6 socket head cap screws (SHCS) for fastening the top of the front faceplate onto the rear of the monitor, sandwiching the display panel
2 - M2x8 SHCS for fastening the bottom of the front faceplate onto the rear of the monitor, sandwiching the display panel
6 - M2x6 heat set inserts for fastening the front faceplate onto the rear of the monitor, sandwiching the display panel
4 - M2x4 SHCS for fastening the display panel to the rear monitor housing
4 - M2x4 heat set inserts for fastening the top of the front faceplate onto the rear of the monitor, sandwiching the display panel
7 - M3x4 SHCS for fastening the electronics cover and the EDP driver board to the rear of the monitor
7 - M3x4 heat set inserts for fastening the electronics cover and the EDP driver board to the rear of the monitor
1 - M3x36 (or longer) SHCS for fastening the hinge joint on the monitor stand to the VESA bracket
1 - M3 hexagonal locknut (or regular hex nut with some threadlocker) to fasten the hinge join on the monitor stand to the VESA bracket
4 - M4x6 SHCS for fastening the VESA bracket to the monitor rear for attaching the stand
4 - M4x6 heat set inserts for fastening the VESA bracket to the monitor rear for attaching the stand
Assembly Instructions:
Start by installing all the threaded heat set inserts in their corresponding holes on each part except for the four M4x6 ones. Be sure to install the inserts for the display panel according to the hole configuration on your panel (there are 8 holes you can choose from, but you only need to populate four). Next, take the four spacers and line them up in the four corresponding holes for the VESA mount on the two rear halves of the monitor housing. The will self-centre thanks to a chamfered edge. Superglue them in place. This was done so that you can still use M4x6 screws and inserts without making the monitor significantly thicker or printing the rear parts with a bed of supports. Now that those holes have been extended to their correct height, install the four heat set inserts we left out earlier.
Next, take the ribbon cable that came with your EDP board and unplug it from the board and connect it to the display panel. Route it such that it comes out through the large square hole in the right rear half intended for it. Also route the speaker wires through the smaller rectangular hole in the left rear half intended for it and ensure enough cable comes out of both to reach approximately where the board would be. Then flatten the ribbon cable and bend it into its final position and mount the display panel into the two rear halves to fix their positions into place. Be sure that you routed the left and right speakers to the correct positions (trace the wires and look at the labels on the EDP board). Both the display cable and speaker cables will be routed behind the panel and the speakers will have to come out near their final positions on the sides of the bottom of the panel (there should be just enough cable to do this, but if you want to extend them feel free to do so if you have an iron and some extra cable + heatshrink. Screw the panel into its four inserts and the rear of the monitor should now behave like one solid piece with the panel.
Mount the front faceplate of the housing onto the monitor, ensuring that you press the speakers into their corresponding holes on the front halves and screw them into place setting everything together. You may want some superglue if there are any warped parts or if anything isn't staying as rigid as it should.
Take the EDP board and mount it into its place on the rear. Then plug in the speakers and display cable that we routed out the rear earlier. Take the USB-A female port we salvaged and solder the JST-PH connector + wire assembly to it with some heatshrink to cover the exposed joints. Be careful that you line up the JST connector pinout on the EDP board with the pinout of the USB port (you can look up the pinout of the USB port and the colours the wires should be online or use a multimeter and test for continuity). The EDP board has its pinout written on the board. Plug that in as well and press the USB port into its recess in the rear right.
Screw the electronics board cover into place with the 3 M3 screws for it. Next screw the VESA mount bracket into place with its four M4 screws. Finally attach the stand to the VESA bracket with the long M3 screw and tighten until snug into the locknut so it's able to be set to specific tilt positions and remain in them.
You can now use the monitor as you would any other monitor and plug in display + power!
This model was created using Fusion 360.