1 / 1
Teleporting Die Trick - Move a die in and out of two boxes at will! Includes optional 3D printed sound-effects! — zdjęcie 1

Teleporting Die Trick - Move a die in and out of two boxes at will! Includes optional 3D printed sound-effects!

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

This fun trick is sure to amaze children and even adults! Teleport a single die in and out of separate closed boxes

Ocena
0 / 5
Polubienia
3
Pobrania
2
Wydruki
0
Wyświetlenia
187
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

Teleporting Die Trick:

Show your audience a normal die, placed behind a curtain, and two empty boxes. Take the die from behind the curtain and place it in one of the boxes. Then, tap the boxes together to teleport the die from one box to the other. 

Amaze with your ability to teleport the die between the two boxes at will! For a grand finale, show both boxes are empty once more, and pull the die back out from behind the curtain!

Non-Printed Bill of Materials

  • QTY 12 6mm OD x 2mm Thick Magnets. Amazon Link (non-affiliate)

    • QTY 14 if using the optional sound-effect base

  • Super Glue, or other adhesive suitable for bonding 3D printed plastic

  • Dark permanent marker to match the front face of the false die to the box (not required, but helps with the illusion when viewed at skew angles)

Printing Considerations:

  1. The objects are rather large (3" cubes) I tried to make them as small as possible while still being fun to interact with (mainly, being able to put your fingers inside of the empty box to show that it is indeed empty).

    1. This project is a GREAT opportunity to use your 0.6mm Nozzle if you have one to reduce print times. Print times are reduced even at the same layer height due to the thin wall features.

  2. Please pay attention to the printing resolutions for each individual piece. Every part can be printed with a 0.6mm nozzle, but some parts need finer layer heights due to the thin walls where magnets are mounted

  3. Use OPAQUE filament

  4. Sparkly filament can help hide the magnet's reflectivity in areas where the walls are thinner 

  5. Print the Die Inserts the same color as the Box

  6. Printing the box a darker color than the die is recommended

  7. You could slice this for MMU printing. I chose to instead glue the colored dots on as the purge towers would be excessive print time and waste for this application.

    1. MMU files are provided in their own folder

  8. You could probably get away without printing the dots at all, and just coloring them in somehow.

    1. Print the False_Die_Body with a fine layer height if you intend to do this. Check in your slicer to make sure you are getting enough layers in the dots on the bottom face. I did not make it this way. YMMV.

Performing the trick:

  1. Seat your audience in front of you with the two boxes square towards them, and the curtain off to the side. Your audience should not be able to see over the boxes or the curtain.

    1. The curtain will have one one False Die behind it, sitting on the table, and one Show Die, sitting on the ledge

    2. One box should be completely empty

    3. The other box should have the other False Die inside, with the False Die Face attached to the Shutter

  2. Show your audience the False Die from behind the curtain, and place it in the empty box

    1. Lift up the curtain to show there is nothing else behind it (the Show Die will be sitting on the ledge). Keep the Curtain from tilting too far up or down as to not reveal the Show Die behind it.

  3. Close the Shutter on both boxes

    1. NOTE: older version of sliding box shown. Posted version does not have a visible seam on the front.

  4. Perform some animation of moving the Die between the two boxes. 

    1. You can "knock" the Die from one box to the other, tip the box as if to "pour" the die from one to another, or use the optional base to "slide" the Die from box to box with an added sound effect. Get creative!

  5. Open the Shutter AND the False Die Face on the original box, to show that the box is now completely empty!

    1. Keep the shutter perpendicular to your audience, so they can not see the different colors of plastic.

    2. I like to wrap my fingers around the front of the shutter as I pull it up to obscure the edge of the shutter.

    3. Pushing the shutter and false die face towards the hole while pulling up helps if your magnets in the false die face aren't totally flush or were mounted un-evenly. 

  6. Open JUST the Shutter on the other box, and the die has magically appeared in that box!

  7. Repeat the trick as many times as you'd like

  8. When you are ready to conclude the trick, you can open the Shutter AND the False Die Face on both Boxes, so that both boxes appear empty

  9. Reveal the Show Die from behind the curtain, and pass it around the audience for inspection, so that they can see there is nothing unusual about it at all. 

    1. NOTE: Don't tilt the curtain too much like I did :) 

Assembly Instructions:

ASSEMBLY NOTICE: It is IMPERATIVE that the magnets are glued in the correct orientation. Stop and make sure that you have the poles oriented correctly before gluing. 
  1. Cut two pieces of 1.75mm filament approximately 75mm long

  2. Insert the filament into the hinge of the Lid and the Box

  3. Cut off excess filament

  4. Glue 2 magnets into each of the Shutters

    1. MAKE SURE ALL FOUR OF THESE MAGNETS ARE POLARIZED IN THE SAME DIRECTION.

    2. How they are polarized in this step is arbitrary, just make sure they are all the same before you glue them in place

  5. Glue 2 magnets into each of the False Die Faces

    1. These magnets should stick to the shutter THROUGH the False Die Face. Place the False Die Face as shown and make sure ALL FOUR magnets stick to the Shutter before gluing.

    2. Push the magnets all the way flush in their holes. Don't let them stick out proud or the trick will be hard to perform.

  6. Glue 2 magnets into each of the False Die Bodies

    1. These magnets should stick the False Die Face to the Die Body

      1. Stick a magnet to the bare side of the magnets in the False Die Face. The side that stuck needs to face OUT of the Die Body (towards the camera in below picture).

      2. Once you are SURE of the orientation, glue the magnet to the Die Body. Push the magnet all the way down into its hole

      3. You can color the mating face of the false die body with a black marker (or whatever color you printed) to match the Boxes, to help with the illusion when viewed at skew angles. 

  7. Add the Die Inserts to the the die. Making sure they are fully and properly seated.

    1. The first insert is easy, just put it in the middle and slide it over

    2. Insert the second insert at around a 30-45 degree angle, then slide it against the outer wall until it is all the way down and in

    3. Make sure the seam between the inserts is perfectly flush and that they are not overlapping

  8. Glue the dots onto the Show Die and both of the False Dice

  9. OPTIONAL: If using the sliding base, glue a magnet into the body and the lid of the base

    1. Make sure the magnets attract eachother

  10. OPTIONAL: Place the sliding weight inside of the box and close the lid. 

Tagi