Library of Alexandria box — a magnetic box under the great dome
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
The Library of Alexandria as a magnetic box, 118 mm. Two prints, 8 buried magnets, 90 × 60 × 45 mm cavity.
- Ocena
- 0 / 5
- Polubienia
- 4
- Pobrania
- 8
- Wydruki
- 0
- Wyświetlenia
- 39
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Organizers
- Licencja
- Creative Commons — Attribution
The Library of Alexandria as a box. A white-marble hall stands behind an arcade of pointed arches, a monumental stair runs the whole width of the front, four square turrets carry small gilded onion domes, and a great ribbed onion dome sits on a chevroned drum in the middle. Everything from the cornice up is the lid.

118 × 96 × 113 mm on the shelf, stair included. 90 × 60 × 45 mm inside.
Not a historical replica — this is the Magic: The Gathering card. Nobody knows what the real Library of Alexandria looked like; no contemporary depiction of it survives. This model is a fan tribute to the Library of Alexandria card from the Magic: The Gathering trading card game — the original Arabian Nights printing, illustrated by Mark Poole — rebuilt from scratch as original OpenSCAD geometry. It is unofficial and unaffiliated: not produced, endorsed, licensed or sponsored by Wizards of the Coast, and it reproduces no card art, logo, frame or text. Magic: The Gathering is a trademark of Wizards of the Coast LLC.
Six STLs, two prints, nothing to glue. Eight Ø5 × 3 mm magnets are buried inside the walls at a print pause — four per half — so nothing shows on the outside and the lid pulls itself shut through 1.2 mm of marble.

Materials
Filament: PLA, ≈190 g sliced at 0.2 mm / 3 walls / 15 % infill — ≈98 g for the base, ≈92 g for the lid. Four colours: marble white, dark brown, lapis blue, gold. Single-filament builders use the two
_stonefiles and about 150 g.Non-printed parts: 8 × neodymium disc magnets, Ø5 × 3 mm. Nothing else — no screws, no glue, no elastic.
Tools: none. Tweezers help drop the discs in at the pause.
The six parts

STL | filament | what it is | |
| A | marble white | plinth, stair, hall, turrets to the cornice, locating tongue, 4 sealed magnet pockets |
| A | dark brown | 15 windows, 8 turret slits and the planked door, each at the back of its pocket |
| B | marble white | roof slab, crest, drum, turret tops, 4 sealed magnet pockets |
| B | dark brown | the 8 drum windows |
| B | lapis blue | 16 chevrons under the great dome + a chequer band on every turret |
| B | gold | five ribbed onion domes and their finials |
Step 1 — slice print A, the base
Import
library_base_stone.stlandlibrary_base_dark.stltogether.Bambu asks "load as a single object with multiple parts?" — answer Yes. They arrive coordinate-locked; do not move them relative to each other.
Assign marble white and dark brown.

Never merge the files and use "Split to Parts." It divides by connected component and ignores solid names, and each
_stonefile carries four sealed magnet voids. A split returns those voids as solid discs that silently re-fill the pockets — and you find out after a five-hour print.
Step 2 — slice print B, the lid
Same again with library_lid_stone.stl, library_lid_dark.stl, library_lid_blue.stl, library_lid_gold.stl → marble white, dark brown, lapis blue, gold.
Blue is one band, z 69–74: the chevrons under the great dome and the chequers on the turrets stop on the same plane, so both cost one set of bi-colour layers. Above z 74 the lid is gold alone.

Step 3 — the two pauses
This is the part to read twice. Each half buries four magnets mid-print. In Bambu Studio, right-click the layer slider → Add pause.
pause at | layer (0.2 mm) | what you see | |
B — lid | 3.8 mm above the bed | 19 | four Ø5.3 holes in the turret corners of the flat underside |
A — base | 49.4 mm | 247 | four Ø5.3 holes in the turret corners, 0.6 mm under the rim |
The lid's pause is four minutes in. The base's is late — set it before you start the print, it is the one that hurts to miss.

At each pause drop one disc into each hole. It sits 0.6 mm below the next layer, which bridges straight over it.
Polarity is a one-way mistake. Print the lid first. At the base's pause, hold each disc against the finished lid's matching corner before dropping it in: the base disc must be the face that attracts the lid there. Check all four.
Missed a pause? Drill Ø5.2 × 3.4 mm into the corner from the mating face and glue the disc in. Pocket centres are 3.5 mm outboard of each turret centre on both axes — 52.5 mm from the centre line along the façade, 37.5 mm front to back.
Step 4 — print
Do not rotate either half.
| Base | Lid |
Stands on | its plinth, widest at the bed | its flat underside, domes up |
Orientation | exactly as exported | exactly as exported |
Supports | none | none |
Every arch is pointed (30° off vertical at the apex) and the stair is a stack of horizontal treads, so the base has no overhang to support.
The domes lean at most 14° off vertical. The only downward faces on the lid are the 1 mm seam-collar step, the 2.8 mm tongue-groove ceiling and the four Ø5.3 mm magnet-pocket ceilings — all short bridges.
Turn ironing OFF on the lid's top faces. The roof and the drum top are bi-colour layers and ironing drags one colour across the other.
Dark-on-white is the cheap flush direction; keep it that way round. Everything above z 74 is gold alone and costs no purge at all.

Step 5 — one colour, if you prefer
Print just library_base_stone.stl and library_lid_stone.stl and skip the rest. Every accent is a pocket that its plug fills from behind, so without the plugs you still get the whole design as crisp 1.0–1.4 mm engraving — and the magnets still work, because they live in the stone parts.
Step 6 — assemble
Set the lid on the base. The inward tongue locates it with 0.2 mm of clearance per side, the seam hides in a 2 mm recessed shadow line at the cornice, and the magnets pull it home.
If the lid rocks, deburr the elephant's foot on the tongue rather than sanding the groove — the groove's ceiling is a bridge and is the softer of the two.

The .scad source is included if you want a different cavity, a plain dome or a different size.
The geometry is hand-authored OpenSCAD — no AI-generated meshes.
