1 / 5
Dragon Wing Palette Rack — eyeshadow palettes on edge, no supports — zdjęcie 1
1 / 5

Dragon Wing Palette Rack — eyeshadow palettes on edge, no supports

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Eyeshadow palettes stood on edge in a dragon's wing. Five slots, no supports, no hardware, one part.

Ocena
0 / 5
Polubienia
2
Pobrania
5
Wydruki
0
Wyświetlenia
22
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Bathroom
Licencja
Creative Commons — Attribution

Dragon Wing Palette Rack

Palettes are the one makeup item nobody stores properly. They are flat, they stack, and the bottom one is never seen again. Stand them on edge and every palette is a spine you can read and pull out one-handed — the way you shelve books, not the way you pile plates.

This is that rack, and its fins are the finger bones of a dragon's wing.

1 part · 118 × 128 × 112 mm · no supports, no hardware, no assembly. One STL, one print, flat on its base.

What it holds

5 slots, 16.5 mm wide ......... anything up to an 18 mm palette 100 mm clear depth ............ between the front rail and the back spine Shortest fin 76 mm ............ a 100 x 100 palette is held over 3/4 of its height Tallest fin 106 mm

Stand palettes on edge, hinge down, spine out. The front rail stops them tipping out and the back spine is what they lean on.

It cleans out

The floor is one open, wipeable plate. Nothing in the part is enclosed and there is no blind pocket anywhere — lift the palettes out and wipe straight through. Loose pigment does not get to live in a corner you cannot reach.

Why the fin is shaped like that

Every segment of the fin profile is upward-facing, and that is what lets a 112 mm tall part print with zero supports. It is a property of the two curves rather than luck:

  • the leading edge is fin_y0 + 4 + 70·t^2.2 — the exponent keeps the lower half nearly vertical, which is what actually guides a 100 mm palette sideways, and throws the whole sweep into the top third where the talon wants it;

  • the membrane's scooped trailing edge is a quadratic Bézier whose control point is pulled up and forward. A scoop that gets its concavity by letting the curve fall away puts a downward-facing surface on the back of every fin.

The lancet windows are pointed arches for the same reason — a round or square window has a ceiling. They are intersected with the membrane eroded by 7 mm, so they cannot break an edge or clip their own apex flat whatever the fin height.

This is measured, not asserted: the model's own gate totals every downward-facing face above the bed and sums the ones shallower than 45°. That total is 0.00 mm².

Printing

dragon_wing_palette_rack.stl 1x 118 x 128 x 112 mm

0.2 mm layers, 3 walls, 15 % infill, no supports, no brim needed — the base is a 118 × 128 mm flat plate. Print it in the orientation the STL is saved in.

386 g if it were printed solid; at 15 % infill expect roughly 180–200 g.

Supports only make a mess here — every overhang in the part is 45° or steeper, including the pointed windows.

Parametric

The OpenSCAD source ships with it. Slot width, slot count, fin heights, the clear depth and the window shape are all named variables at the top of the file, so the rack can be re-cut to whatever is actually on your table — wider slots for thick palettes, more fins, or a shallower fan.

part= rack | loaded | fin | section.

Tagi