1 / 3
Half-Amphora Brooch — a real amphora, full of flowers, cut in half — zdjęcie 1
1 / 3

Half-Amphora Brooch — a real amphora, full of flowers, cut in half

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A turned amphora full of flowers, cut in half — 6 mm of real relief, no supports. Magnetic back, no pin.

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
11
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

Most vase brooches are a flat silhouette of a vase. This one is a real amphora.

The body is turned as a solid of revolution from a table of [height, radius] pairs, given two swept handles and five flowers standing in it — and then the whole object is cut in half on the plane of the brooch's back. What is left is 6 mm of true 3D relief with a flat back that sits against the fabric. The handles have a real opening under them; you can get a fingernail through.

Plaque 44 × 58 × 11 mm · backer 32 × 18 × 4.3 mm · ≈20 g of PLA for the pair.

the printed brooch — pink body, off-white ground, vermilion blooms, green leaves

The halving is also the print trick

Take a solid of revolution about a vertical axis and cut it on the plane z = 0. At height y the profile radius is r(y), and the section at depth z is |x| ≤ √(*r(y)*² − *z*²) — which only ever shrinks as z grows.

Every horizontal slice of this part is therefore narrower than the one below it. A shape made of nothing but curves, standing 6 mm proud, with no overhang anywhere and no supports. The handles and the flowers are halved on the same plane for the same reason.

Print it exactly as exported: front face up, flat back on the bed.

Two printed pieces, seven named solids

Import half_amphora_brooch_mc.stl → right-click → Split to Parts → assign a filament per part. Nine parts appear, because plugs and backer_seals are two pieces each.

every solid, in mating order

solid

slot

role

plate

1 — warm bone

the plaque, the amphora and its two handles

plugs ×2

1

fill the bore over the plaque's magnets, up to the ground

ground

2 — umber

the background the amphora stands against

blooms

3 — vermilion

five flower heads, welded into one shell

leaves

4 — leaf green

stems and leaves — the green half of the spray

backer

1

the 4.3 mm plate that sits behind the fabric

backer_seals ×2

1

its two magnet lids

Coordinates are preserved exactly, which is the point — a 0.6 mm flush inlay cannot be re-registered by hand. The per-part STLs ship alongside if you would rather place them yourself.

The 32 × 18 backer is the same part as every other brooch in this family, so if you already have one, print half_amphora_brooch_nobacker_mc.stl instead.

Colour costs height, not volume

the four colours flat on — the spray and the ground are the only ink

≈6 g of purge, and two bands carry all of it: the ground at z 4.40–5.00, and the spray from z 5.00 to about 6.3. The blooms and the leaves deliberately occupy the same band, so they share their colour changes instead of doubling them.

The background shows body colour inside the handle apertures rather than umber, which keeps each handle reading as solid.

Printing

 

value

Orientation

as exported — front up, flat back on the bed

Layer height

0.2 mm (0.12 mm is visibly better on the turned belly)

Supports

none

Walls

3

Plate

plaque + backer together

Turn ironing OFF — four colours meet near the top face, and ironing drags one across another.

⏸ The magnet pause — Z = 3.70 mm, after LAYER 19, at 0.2 mm layers

Right-click the layer slider at that height → Add Pause. One pause serves the whole plate: the plaque and the backer bury their magnets at the same height on purpose. Four wells open — two in the brooch, two in the backer. One Ø5 × 3 mm neodymium disc per well, then resume.

The magnets end up completely enclosed — no part of one is visible in any finished face, and there is nothing to glue.

Each magnet finishes 0.6 mm from the back face — the face that pulls against its partner — so only 1.3 mm of plastic sits between the two magnets. The pull between two discs falls off as roughly the fourth power of that gap, so it is the only number that matters. Everything above each magnet is closed by the plugs and backer_seals solids, printed in place. The pair sits at the plaque centre, so there is no lever arm on a brooch this tall.

Polarity — the step that actually goes wrong

Four discs, exactly one arrangement works:

  • all four the same way round → the two pieces repel;

  • one of a pair flipped → one station attracts, the other repels, so the brooch sticks, pivots on the good magnet and hangs crooked. This is the sneaky one — it feels fine when you test it with a fingertip.

While the printer is paused: let all four magnets stack into one column (they are now alternating N-S-N-S), split it into two pairs, pull each pair apart and mark the two faces that were touching. Those two must end up facing each other across the fabric. Both plaque magnets go in marks up; both backer magnets marks up as well.

Wearing it

Plaque in front of the fabric, backer behind, slide the pair where you want it. No pin, so nothing pierces the cloth — safe on knitwear, silk, a lapel, a canvas bag, a hat.

Two magnets across a fold of fabric is a firm grip, not a permanent one. On something thick — a heavy wool coat, a padded jacket — the extra gap costs a lot of force. Test it before wearing it out.

⚠ Keep the magnets away from pacemakers, and away from phones, cards and watches. Four small neodymium discs are not toys — swallowed magnets that find each other through the gut wall are a surgical emergency.

Parametric source

The .scad is included. The amphora is a plain table of [height, radius] pairs, so you can turn a different vessel by editing numbers: depth_k squashes the relief, handle_out moves the handles off the axis, handle_r fattens the tube, and the flower spray is its own small set of parameters.

Tagi