Moonwake Makeup Wardrobe — a 240 mm two-door cabinet with printed hinges and lift-off door bins
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A 240 mm two-door makeup cabinet: printed hinges, four lift-off door bins, two removable organizers.
- Ocena
- 0 / 5
- Polubienia
- 4
- Pobrania
- 8
- Wydruki
- 0
- Wyświetlenia
- 56
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Organizers
- Licencja
- Creative Commons — Attribution
A wardrobe for makeup, brushes and bathroom clutter. Two engraved doors swing open on four printed pins, four bins lift off the door panels, and two organizers slide out of the cabinet so you can wipe every surface.
240 × 200 × 228 mm closed. Allow about 460 mm of width with the doors at 160°, and room in front to pull the organizers out.

No hardware anywhere. No screws, no magnets, no glue, no AMS. The hinge pins are printed parts, gravity-retained, and pull straight out if you want the doors off.

What holds what
Inside, back left: a brush pod — two deep wells for brushes standing on their handles.
Inside, back right: a rack — five tube cells across the front, two upright palette slots behind them.
The whole front floor stays clear for bottles, jars, sponges and compacts.
Four door bins, two per door, about twelve small tubes' worth. They slide down a dovetail rail onto a stop and lift off in 34 mm.
Both organizers came from the open Moonwake vanity and are reused unchanged, so the same parts work on a shelf if you ever take them out.
The joints
Hinges. A 4.0 mm printed pin in a 4.6 mm bore: 0.3 mm radial clearance, 0.6 mm axial clearance at each end of the middle knuckle. The bores are teardropped so no circular hole has to bridge its own roof, and the thinnest barrel wall is 1.7 mm. Pins drop in from above, head up, and stay in by gravity.
Bins. A dovetail sleeve over a rail on the door panel, 0.4 mm profile clearance, resting on a printed stop. It must slide without force, stay captured when you pull it away from the door, and lift off upward.
Doors. Closing stops, no latch. They stay shut by their own geometry, not by a catch — this is a cabinet, not a case you carry.
Print it — 10 files, 16 pieces
File | Qty | Each | Each time |
| 1 | 756.1 g | 621 min |
| 1 | 74.4 g | 96 min |
| 1 | 74.4 g | 96 min |
| 4 | 23.6 g | 28 min |
| 4 | 0.7 g | 7 min |
| 1 | 128.9 g | 131 min |
| 1 | 177.5 g | 206 min |
| 1 | 3.9 g | 12 min |
| 1 | 3.4 g | 7 min |
| 1 | 5.5 g | 10 min |
About 1.32 kg and 22 hours in total, coupons included; have 1.45 kg available across the colours. Measured in Bambu Studio 2.7.1.57, P2S / 0.4 mm / 0.20 mm Standard / PLA Basic, three walls, 12 % infill, supports off. Every file slices without a warning.
A 256 mm bed is required. The cabinet alone is a 240 × 228 mm footprint and about 10 h 21 min; it does not fit an A1 mini.
Import at 100 % and keep the supplied orientation: cabinet back down and opening upward, doors decorated face down, bins and organizers upright, pins head down. Pins only: five walls and a 3 mm outer brim — they are 0.7 g sticks and will otherwise walk off the plate. Cut the brim off without nicking the head.
Print the three coupons first
coupon_frame, coupon_door, coupon_rail, plus one hinge_pin and one door_bin — about half an hour, against ten hours of cabinet.
Nest the door coupon between the frame knuckles, drop the pin in from above: it must turn freely without forcing. Hold the rail coupon upright, lower the bin's sleeve over it until it rests on the stop: it must slide without force and stay captured when pulled outward.
The pin and the bin are reused in the final build, so afterwards you print only three more of each. If a joint binds, knock elephant-foot burrs off first and only then change bore_d or rail_fit in the source.
Assembly — 13 steps, no tools but flush cutters

1–4. Left door. Stand the cabinet upright, opening toward you. Nest the door's two middle knuckles between the cabinet knuckles, hold the door, and push the lower pin down through all three knuckles until the head seats. Then the upper pin. Check it swings.


5–7. Right door. The same again on the other side. With both doors on, check they reach their closed stops without rubbing.

8–11. Four bins. Doors open. Slide each bin's sleeve down its rail until it rests on the stop — lower rail first, then upper, on each door.

12–13. Two organizers. With the doors at 160°, pass the brush pod through the opening to the back left, then the tube-and-palette rack to the back right. Leave about 6 mm between them.


Living with it
Keep the loads light and do not carry it loaded or lift it by a door. Open the doors fully to pull the organizers out for cleaning; the bins come off in 34 mm. Store brushes dry. Not dishwasher safe — PLA softens in a hot car, let alone a dishwasher.
Parametric source
The OpenSCAD source is included and everything dimensional is a named variable at the top: W / D / H for the case, hinge_levels and hinge_span for the hinge geometry, bore_d and axial_gap for the pin fit, rail_fit for the bin slide, bin_levels / bin_w / bin_h for the bins, open_angle for the swing, and engrave_depth for the crescent and wave relief. wardrobe.scad is the cabinet; it uses moonwake_vanity.scad for the two organizers, so keep both files side by side to rebuild.
