Volvo XC70 / V70 / S60 P2 storage and cup holder
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Drop-in replacement for the center console storage tray on Volvo P2 cars (XC70 3409847 / 9204996 / 30643182
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 16
- Wydruki
- 0
- Wyświetlenia
- 187
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Drop-in replacement for the center console storage tray on Volvo P2 cars (XC70 2003-2004 verified, part numbers 3409847 / 9204996 / 30643182), plus a removable cup caddy that drops into it. Fits the OEM mounting points: two screws and a locating pin at the front, a slotted center screw boss underneath, and two snap hooks at the rear. Same flange outline and skirt as the original, so nothing else in the console has to change.
The set is modular. The tray works on its own as a three compartment storage box. The caddy drops into the front big compartment without tools and lifts out in a second, so the same console is either storage or a cup holder plus storage, depending on the trip. If you only need the tray, print only the tray.
What is different from the original:
- Deeper. The tray goes down to 84 mm instead of about 62 mm, using the full depth of the tunnel.
- Three compartments instead of two: a 20 mm slot at the front for cards standing on edge, then two equal compartments 76 x 92 mm, 79 mm deep.
- Center screw boss has a 14 mm slot along the car axis to absorb measurement tolerance.
- Removable cup caddy (separate file). One round pocket: a 67 mm cylinder at the bottom for 0.33 / 0.5 l cans, a cone widening to 80 mm above it for paper coffee cups. The skirt goes 33 mm into the compartment and the rim stands 60 mm above the tray, so a cup is held low and does not rock. Drain hole in the floor. It fits the front big compartment (the one behind the card slot), the rear compartment stays free.
Dimensions were taken from the original part with calipers and a traced outline, then tuned over several test prints and fittings in the car. Dimensions of the tunnel can vary a little between cars, check the first print before you throw the old part away.
Files:
- volvo_base_v12.stl: the tray, one piece, 246 x 120 x 84 mm.
- volvo_caddy_v6_comp1.stl: cup caddy, 91 x 107 x 93 mm.
Material: PETG or ASA. Do not use PLA for the final part, a car interior gets hot enough to deform it. PLA is fine for a fit test.
Print orientation:
- Tray: face down (flange on the plate). Supports on build plate only, tree/organic. They are needed under the tongue with the screw bosses, inside the compartments (the floors are printed as ceilings), under the center boss and under the rear hooks. Everything else prints without support. No brim needed.
- Caddy: bottom down. Support only under the plate overhang (7.5 mm ring at 33 mm height). Brim recommended, the contact area is small.
Suggested settings: 0.2 mm layers, 4 walls, 20-25 percent infill, 5 top / 4 bottom layers, thin wall detection on. See the print profile.
Installation:
1. Remove the old tray: two screws and the pin at the front under the tongue, the center screw from below, then unhook the rear clips.
2. Insert the new tray rear first so the hooks catch, then press the front down until the pin and the two legs seat.
3. Fit the two front screws and the center screw from below.
4. Drop the caddy into the front big compartment. To get to the compartment, lift the caddy out by the rim.
