Parametric spice tube carousel — for 20 mm test-tube spice vials
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Five tall tubes upright and grabbed one-handed. One piece, no supports. Source included: resize to any tube.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 22
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Kitchen
- Licencja
- Creative Commons — Attribution — Share Alike
Those gift sets of spices in tall glass-look tubes come in a flat wooden box.
It looks good on a shelf and it is a nuisance at the hob: you have to open the lid and slide a tube out sideways, usually with one hand already busy.
This holder stands five of them upright instead. The tube drops in, stands 112 mm proud so you can read the label from across the worktop, and lifts out with two fingers.
WHAT IT IS
* 67.4 mm across, 73.0 mm tall — five pockets on a circle
* sized for tubes of 20 mm diameter and about 180 mm long
* pockets are 20.7 mm wide and 70 mm deep
* closed band at the bottom, windows higher up so you can see the spice and
push a tube out with your thumb
* one piece, printed upright, no support material anywhere
PRINTING IT
No supports. The geometry is built so nothing overhangs by more than 45 degrees: the window heads come to a point instead of bridging, the pocket mouths are chamfered so the opening widens upwards, and the bottom edge is chamfered rather than rounded.
* 0.4 mm nozzle, 0.2 mm layers
* 3 perimeters, 10-15 % infill
* no supports, no brim needed
* PLA or PETG
* roughly 2h55m and 86g
One setting is worth changing from the default profile: set the extrusion width to 0.4 mm. The ribs between the pocket mouths are exactly 1.2 mm, which is three lines of 0.4 — leave the width on automatic and the slicer fits two fat lines instead.
GET THE FIT RIGHT FIRST
An FDM printer cuts holes roughly 0.2-0.3 mm narrower than drawn, and by a different amount on every machine. A pocket that is too tight turns the holder into a puzzle; too loose and the tubes rattle.
So there is a second file: a flat coupon, 131 x 37 x 12 mm, with five pockets cut at different clearances and the value engraved beside each one. Print it first, with the same profile you will use for the holder, try a tube in each hole, and keep the one that drops in and lifts out without effort. On my Prusa MK4 at 0.2 mm that was 0.7 mm, which is what the model here uses. Yours may differ.
If it does, you do not have to live with it — see below.
DIFFERENT TUBES, DIFFERENT COUNT, DIFFERENT HEIGHT
The model is not an STL somebody exported once. It is a Python program written with build123d, and every dimension is a parameter:
uv run scripts/export.py --clearance 1.0 # looser pocketsuv run scripts/export.py --tube-dia 25 # fatter tubes
uv run scripts/export.py --n-slots 8 # a bigger set
uv run scripts/export.py --holder-height-ratio 0.5 # a taller holder
Source, full instructions and the reference photographs:
https://github.com/amedeos/spicy-box
LICENCE
The model and the exported geometry are CC BY-SA 4.0. The Python source that generates them is GPL-3.0. Remix either, share your changes the same way.
It validates what you ask for, too. Widen the windows past the point where a tube would fall out sideways, or ask for a holder so deep there is nothing left to grab, and it tells you in a sentence instead of printing it.