1 / 12
1/2 Federal Signal Q siren — zdjęcie 1
1 / 12

1/2 Federal Signal Q siren

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Got bored, made this

Ocena
0 / 5
Polubienia
17
Pobrania
216
Wydruki
0
Wyświetlenia
953
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Engineering
Licencja
Creative Commons — Attribution — Share Alike

This is a Half scale replica of a Federal Signal Q siren.

Parts list:
Motor: https://www.amazon.com/dp/B0BB2V8PNK?ref_=ppx_hzsearch_conn_dt_b_fed_asin_title_14
Screw kit for motor: https://www.amazon.com/dp/B0F8V7G8T8?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1
Screw kit for body: https://www.amazon.com/dp/B0DFWYBJJJ?ref=ppx_yo2ov_dt_b_fed_asin_title
Screws for Intake Net: https://www.amazon.com/600pcs-Screws-Assortment-M3-Cabinet/dp/B0GYX16FMF/ref=sr_1_1_sspa?crid=3P99WVPZUL5ND&dib=eyJ2IjoiMSJ9.PO4VcxOIHlh0cPhW5q135PscMnLpi4AjQP2qcsM_wXjU9OmwhMgrgaDlEv2TtB8WM1j9Cs7ykp-HxBWvMZMtiJzPpRqW11FiOm-XZ_oF6Hc1F58su4Pq9EPOy5qmOgGcxuPXBsmiyu-dcDrdysxgH7YmLembqGZSvyZa1vo3IjpWjb-cO9MiymReZpxM4fXtJAiMNZbW8B32Mxhsd7gIDdwVoUY19gYPsOPcyaLaUHmp8RVknerEjXJ1QmDY1Hczgqhho0RE8xvx3hhB7Gc_OAHOSCONOnkv32EB6Pclqso.VAHUsJ32HwaAANWFlLqBWgQA9nsRTkUa6PIVVStw-q8&dib_tag=se&keywords=m3%2Bwood%2Bscrews&qid=1789761306&s=industrial&sprefix=m3%2Bwood%2Bscrews%2Cindustrial%2C154&sr=1-1-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9hdGY&th=1
M3 Threaded Inserts: https://www.amazon.com/dp/B08BCRZZS3?ref=ppx_yo2ov_dt_b_fed_asin_title&th=1
Shaft coupler: https://www.amazon.com/dp/B0F3HNS1KW?ref=ppx_yo2ov_dt_b_fed_asin_title





The assembly is simple

Insert the Shaft coupler into the rotor, Make sure the holes are lined up. DON'T USE THE SET SCREWS THAT CAME WITH IT, USE M3x35 SCREWS
Align the pegs on the Motor/Stator holder and Glue then together
Screw the motor into the stator
Add the M3 Threaded inserts in the 3 large holes on the Stator/motor holder.
Glue the Stand in the front, and plastic weld it on the back, On the Motor/stator holder.
Add some weights to the back of the bullet if it's too front heavy.

GRILL
The Mesh ring is plastic welded too the Screen Holder, And the Federal Logo is then Glued on, MAKE SURE THE FEDERAL LOGO IS UP WRITE WHEN IT IS GLUED ON.

Stator Screen
Glue the two halfs together and side it onto the stator, but leave about 8 mm hanging off.
Then, Get the Intake Screen and stick the 8mm into the inside, while keeping the holes aligned.
Then, Press it on, make sure the holes are aligned, and put the four screws in.

YAYAYAYAY you have a half scale Q now

You can run it on a car battery, However not for long, I will update this when I have found a proper power source.