1 / 7
Gehäuse Voice Satellite mit Lautsprecher für Home Assistant | Seeed reSpeaker XVF3800 + Seeed Mono Enclosed Speaker 4R 5W — zdjęcie 1
1 / 7

Gehäuse Voice Satellite mit Lautsprecher für Home Assistant | Seeed reSpeaker XVF3800 + Seeed Mono Enclosed Speaker 4R 5W

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Enclosure for the reSpeaker XVF3800 with XIAO ESP32S3 and the 5 W speaker: a compact voice satellite for HomeAssistant

Ocena
0 / 5
Polubienia
1
Pobrania
30
Wydruki
0
Wyświetlenia
231
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Gadgets
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

🇩🇪 Deutsch

reSpeaker XVF3800 Gehäuse mit integriertem Lautsprecher: Voice-Satellit für Home Assistant

Ein kompaktes, rundes Gehäuse für das reSpeaker XMOS XVF3800 4-Mic Array mit XIAO ESP32S3 von Seeed Studio. Es ist um einen Lautsprecher-Unterbau für den Seeed Mono Enclosed Speaker 4R 5W erweitert.

Als Basis habe ich die offiziellen 3D-Dateien von Seeed Studio verwendet. Dort ist allerdings kein Lautsprecher vorgesehen, und für einen vollwertigen Sprachassistenten braucht man genau diese Kombination. Deshalb habe ich das Gehäuse in Fusion 360 überarbeitet und ein passendes Unterteil für den Lautsprecher konstruiert. Ich nutze das Ganze als Voice-Satellit für Home Assistant.

Features

  • Oberteil für das reSpeaker-Board mit Öffnungen für die 4 Mikrofone und den LED-Ring (12 RGB-LEDs)

  • Seitliche Aussparungen für USB-C und die 3,5-mm-Klinke

  • Unterteil mit Halterung für den Lautsprecher. Dieser strahlt nach unten ab, und der Schall tritt durch die Aussparungen zwischen den Füßen aus.

  • Der Lautsprecher zeigt von den Mikrofonen weg. Das reduziert die direkte Einkopplung und hilft der Echo-Unterdrückung (AEC) des XVF3800.

  • Ober- und Unterteil werden per Clips verbunden.

Benötigte Hardware

  • 1× reSpeaker XMOS XVF3800 4-Mic Array mit XIAO ESP32S3 (Seeed Studio)

  • 1× Mono Enclosed Speaker 4R 5W (Seeed Studio, 50 × 45 × 22 mm)

  • 2 × Einschmelzmutter M3

  • 2 × M3x(7-15mm) Schrauben für die Lautsprecherbefestigung

  • USB-C-Kabel und Netzteil

Druckeinstellungen

  • Material: Nach eigenem Geschmack, ich habe Extrudr Biofusion verwendet

  • Schichthöhe: 0,2 mm

  • Wände / Infill: 3 Wände / 15 %

  • Oberteil: mit der Oberseite aufs Druckbett, praktisch ohne Support (nur kleine Stützen an den seitlichen Öffnungen)

  • Unterteil: stehend auf den Füßen, mit Tree-/Organic-Supports unter dem Speichengitter und den Bögen zwischen den Füßen

  • Getestet auf einem Voron 2.4

Zusammenbau

  1. Zwei Einschmelzgewinde in das Unterteil eindrücken.

  2. Den Lautsprecher von unten an das Speichengitter im Unterteil schrauben, mit der Membran nach unten.

  3. Das Lautsprecherkabel nach oben führen und am JST-Lautsprecheranschluss des reSpeaker einstecken.

  4. Das reSpeaker-Board ins Oberteil einsetzen. Die Seite mit dem Seeed-Logo (Mikrofonöffnungen) zeigt zur Oberseite.

  5. Das Oberteil auf das Unterteil setzen und einrasten lassen.

  6. USB-C anschließen, fertig.

Software
Für den Betrieb mit dem XIAO ESP32S3 muss auf dem XVF3800 die I2S-Firmware laufen. Die Einbindung erfolgt über ESPHome in Home Assistant Assist. Bei mir läuft alles komplett lokal mit Whisper (Spracherkennung) und Piper (Sprachausgabe).


🇬🇧 English

reSpeaker XVF3800 Enclosure with Integrated Speaker: Voice Satellite for Home Assistant

A compact, round enclosure for the reSpeaker XMOS XVF3800 4-Mic Array with XIAO ESP32S3 by Seeed Studio. It is extended with a speaker base for the Seeed Mono Enclosed Speaker 4R 5W.

I started from Seeed Studio's official 3D files. They don't include a speaker, though, and a proper voice assistant needs exactly this combination. So I reworked the enclosure in Fusion 360 and designed a matching base for the speaker. I use it as a voice satellite for Home Assistant.

Features

  • Top part for the reSpeaker board with openings for the 4 microphones and the LED ring (12 RGB LEDs)

  • Side cutouts for USB-C and the 3.5 mm jack

  • Base with a mount for the speaker. It fires downwards, and the sound exits through the gaps between the feet.

  • The speaker points away from the microphones. This reduces direct coupling and helps the XVF3800's echo cancellation (AEC).

  • Top and base snap together with clips.

Required hardware

  • 1× reSpeaker XMOS XVF3800 4-Mic Array with XIAO ESP32S3 (Seeed Studio)

  • 1× Mono Enclosed Speaker 4R 5W (Seeed Studio, 50 × 45 × 22 mm)

  • 2 × Heatsetinsert M3

  • 2 × M3x(7-15mm) Screws for Speaker

  • USB-C cable and power supply

Print settings

  • Material: Wich you prefer, i used Extrudr Biofusion

  • Layer height: 0.2 mm

  • Walls / infill: walls / 15 %

  • Top part: top face down on the bed, practically no supports (only small ones at the side openings)

  • Base: standing on its feet, with tree/organic supports under the spoke grid and the arches between the feet

  • Tested on a Voron 2.4

Assembly

  1. Insert the Heatsetinserts into the bottom part

  2. Screw the speaker to the underside of the spoke grid in the base, with the membrane facing down.

  3. Route the speaker cable upwards and plug it into the reSpeaker's JST speaker connector.

  4. Place the reSpeaker board in the top part. The side with the Seeed logo (microphone ports) faces the top.

  5. Put the top part onto the base and let it snap in.

  6. Connect USB-C, done.

Software
To use it with the XIAO ESP32S3, the XVF3800 needs to run the I2S firmware. It is integrated into Home Assistant Assist via ESPHome. My setup runs fully local with Whisper (speech-to-text) and Piper (text-to-speech).

Tagi