1 / 3
Beseler 23C Negative Carrier – 6 x 4.5 (645) — zdjęcie 1
1 / 3

Beseler 23C Negative Carrier – 6 x 4.5 (645)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Hinged, one-piece printable Beseler 23C negative carrier for 6x4.5 (645) on 120/220: Mamiya 645, Bronica ETR series.

Ocena
0 / 5
Polubienia
2
Pobrania
16
Wydruki
0
Wyświetlenia
30
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Photo & Video
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

⚠ Please Read the Instructions First

These carriers work like the original Beseler carriers, but they are plastic, not metal, and plastic has to be handled differently. The included PDF walks through printing and assembly step by step. Following it is the surest way to a carrier that works the way it should.

Printable replacement negative carrier for Beseler 23C-series enlargers, for 6x4.5 (645) negatives.

Hinged, One-Piece Carrier

Works like the original Beseler carriers. The top plate is joined to the bottom by a print-in-place hinge, so it opens, loads and closes exactly like the OEM part. This is not a two-piece sandwich you have to assemble before it goes into the enlarger.

Only additional items needed: CA (super) glue and a hammer.

Not for Commercial Use

This model is licensed under Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International (CC BY-NC-SA 4.0): http://creativecommons.org/licenses/by-nc-sa/4.0/ Print it for yourself, for friends, or for your camera club. Selling prints or files, whether on eBay, Etsy, print-on-demand services or anywhere else, requires a commercial license. Contact me to arrange one.

Specifications

  • Enlarger: Fits Beseler 23C-series enlargers (23C, 23C Series II, 23CII, 23CIII).

  • Film: 120/220 roll film

  • Used with: Mamiya 645 series (M645, M645 1000S, M645J, M645 Super, 645 Pro, 645 Pro TL, 645E, 645AF, 645AFD), Bronica ETR, ETRC, ETRS and ETRSi, Pentax 645, 645N and 645NII, Contax 645, Hasselblad H1 and H2, Fuji GA645 and GS645, Holga 120N and 120GCFN with the 6x4.5 mask, and 6x4.5 folders

Print Settings

  • 0.08 mm layer height, 0.4 mm nozzle

  • PLA, opaque matte black recommended (pins may be a light color)

  • Print on the smoothest plate you have; avoid textured plates

  • Do NOT use any XY hole compensation; the pin holes are an interference fit

  • Top and bottom usually need separate plates

Files

  • Negative_Carrier_Beseler_23C_6_x_4_5_Bambu.3mf (Bambu Studio)

  • Negative_Carrier_Beseler_23C_6_x_4_5_Generic.3mf (other slicers, tested in PrusaSlicer)

  • Negative_Carrier_Beseler_23C_6_x_4_5_top.stl (top plate with print-in-place hinge)

  • Negative_Carrier_Beseler_23C_6_x_4_5_bottom.stl (bottom plate)

  • NegativeCarrier_Aligment_Pins_Undercut_All.stl (4 pins per carrier)

  • Beseler_23C_45_Negative_Carrier_Printing_And_Assembly_Instructions.pdf

Assembly

Full steps are in the included PDF: drive the 4 undercut pins, break the print-in-place hinge free, then glue the hinge to the bottom plate with CA glue.

Support This Work

Every carrier here is free and always will be. If one has earned a place in your darkroom and you'd like to say thanks, the tip jar is here: https://www.printables.com/@jschwefel_1261537/collections/3772975 Thank-you plaques at f/5.6 ($5), f/8 ($8) and f/11 ($11).

Tagi