1 / 3
Land Rover Discovery 1 Headlight Bracket for 7" Lamps — zdjęcie 1
1 / 3

Land Rover Discovery 1 Headlight Bracket for 7" Lamps

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Mounts a 7" round headlight unit into the Discovery 1 (300tdi) or 2 (pre facelift)

Ocena
0 / 5
Polubienia
12
Pobrania
74
Wydruki
0
Wyświetlenia
227
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution

The Bracket:  (Also see notes for V2)
A sturdy mount for a 7" lamp with the mounting points and shape to fit the Discovery 1. There's several design elements to reduce support but it's unavoidable on the roof of the round cavity and around the bottom of the print. The provided model is the right hand side. Mirror it horizontally for the left hand side.
The bracket is designed to tilt the lamp inwards slightly to point straight forwards.

Check:
I don't have any self-levelling system on my D1, so check your own local regulations about the legality of whatever lamps you fit. I think the 200tdi has different headlights and are probably NOT compatible with this bracket. Pre-facelift D2 should be ok but facelift D2 is NOT the same.

Clips:
I've included replacement mount clips that are more sturdy than standard. These attach to the back of the bracket with two screws each.  These should align with the original bulb adjustment rods and are designed to match the original lamp positions, so no adjustment should be required. There's also three bulb mount clips that fit around the circumference of the bulb unit, each needing one screw.

Printing:
I printed mine in PETG with 10% gyroid infill and 4 walls. This uses about 330 grams per bracket. The bracket will print vertically for the least layer lines and needs support. Lay the clips all flat. They should load into your slicer correctly rotated. 

Post Print:
I did smoothen my prints with wet and dry and then spray with "black bumper & trim spray".

Shopping List:
M4 x 20 screws (18 off) - I've used cap head screws with hex bit.

Assembly and Installation:
Place your new bulb unit into the bracket. It should sit easily into the cavity for it. Make sure it's up the right way. The angled corner of a bracket will be the top edge. Place the three bulb retaining clips over the lip of the bulb edge and screw them down. Mount the three bracket clips in the three corners of the bracket. They sit on circular posts and fix down with two screws each.
The original headlight assembly pulls forwards from the body of the car. It's mounted on three ball-and-socket pins, two along the top edge and one bottom outer. Be careful not to break them but they are quite stiff and pull forwards with some force. The replacement unit fits in the same way. Juggle your cables as required.

The photos show my new lights I bought on ebay for less than £20 at the moment, described as "Pair 7" Inch HALO Angel Eyes For Land Rover Defender 90 110 LED DRL Headlights" - I did crimp together a spade-to-spade cable to connect the sidelight to the car's positive socket.

24th Sep 2026 - very minor revision that adds a marker for the top of the bulb, to help align rotation.

26th Sep 2026 - quite a substantial revision that changes the front face chamfer and pulls the top outer corner backwards for a better profile when fitted. I've made the outer walls thin, and a few other refinements to reduce support.

28th Sep 2026 - optional extra spacers in case the bracket meets the metal and prevents the ball-and-sockets from connecting.

29th Sep 2026 - increased the polygon count to make the front face smoother. You may not even noticed once it's printed and painted.