Belt tensioning device
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Modifying the tensioner pulley mount on the Core One
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 0
- Wydruki
- 0
- Wyświetlenia
- 98
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Prusa Parts & Upgrades
- Licencja
- GNU General Public License v2.0
Beschreibung
Am günstigsten ist die Schraube zum Spannen der Riemen angeordnet, wenn sie genau mittig vor der jeweiligen Spannrolle sitzt.
Aus den veröffentlichen CAD Daten ergibt sich ein Achsabstand von 364 mm bei einer Höhendiferenz von 10,8 mm.
Um diese Schrauben bewegen zu können, müssen die vorderen Blechprofile gebohrt werden und entsprechende Schraubenhalter (Sättel) hergestellt werden.
HolmSattelVF.stl und RollenGabelVF.stl müssen je 2 x gedruckt werden. Ich verwende Spectrum PCTG-GF10. HolmSchabloneVF.stl wird nur einmal benötigt. Dafür reicht sicher PLA
Ich verlasse mich lediglich darauf, dass Löcher genau an Ort und Stelle sind, die genaue Größe von Gewinde und Bohrungen bearbeite ich immer nach.
Ausgangspunkt für die Befestigung der Sättel sind die vorhandenen 8 mm Bohrungen durch die bisher das Spannen erfolgte.
Die alten Halter für die Umlenkrollen werden nicht mehr benötigt. Die Rollen und die M3 Schrauben werden wieder verwendet.
Der Türsensor wird dadurch unbrauchbar und der Schacht für den Dock Fan des INDX lässt sich nicht mehr anschrauben. Für beide zwei andere Ausgaben auf Printables.
Der Endschalter wird später in das obere Türgelenk integriert und der Schacht mit dem oberen Türmagnet verbunden.
Nachdem die Profile abgeschraubt sind, wird die Schablone mit einer Senkkopfschraube M5x10 in einem Holm eingeschraubt.
Durch die beiden 3 mm Bohrungen können jetzt mit einem Zentrierkörner die neuen Bohrungen angekörnt werden.
Das gleiche beim zweiten Profil. Die Schablone wird nun nicht mehr benötigt.
Danach werden die Bohrungen vorsichtig mit kleinen Bohrern vorgebohrt und anschließend mit einem Stufenbohrer von beiden Seiten auf 6 mm bzw. 8 mm erweitert.
Die mittlere Bohrung muss nur soweit vergrößert werden, dass der 2,5 mm Inbusschlüssel ohne zu klemmen durchgeht.
Unbedingt Entgraten; Verletzungsgefahr!
In die Sättel kommt je eine Schraube M3x35 mit einer möglichst großen Unterlegscheibe damit sich der Schraubenkopf nicht eingräbt.
Die Sättel mit je 2 Senkkopfschrauben M5x10 befestigen und die Profile wieder montieren.
Die Rollengabeln sind für Einschmelzeinsätze M3 von der Gabelseite her ausgelegt.
Zum Schluß noch die Riemen mit den Rollen und den alten Schrauben montieren und die Riemen neu spannen.
Machine Translated by Google:
Description
The belt-tensioning screw is most effectively positioned when located exactly in the center, directly in front of the respective tensioner pulley.
Based on the published CAD data, the center-to-center distance is 364 mm with a vertical offset of 10.8 mm.
To accommodate these screws, holes must be drilled into the front sheet-metal profiles, and corresponding screw mounts (saddles) must be fabricated.
Two copies each of HolmSattelVF.stl and RollenGabelVF.stl need to be printed; I use Spectrum PCTG-GF10. Only one copy of HolmSchabloneVF.stl is required; PLA is perfectly adequate for this part.
I rely on the holes being in the correct general location, but I always finish-machine the threads and bore diameters to exact specifications.
The existing 8 mm holes—previously used for tensioning—serve as the starting point for mounting the saddles.
The old idler pulley mounts are no longer needed; the pulleys and M3 screws will be reused.
This renders the door sensor unusable and prevents the INDX dock fan duct from being screwed on; there are alternative versions for both available on Printables.
The limit switch will later be integrated into the upper door hinge, and the duct will be connected to the upper door magnet.
Once the profiles have been unscrewed, the template is attached to a rail using an M5x10 countersunk screw.
The new hole locations can now be marked through the two 3 mm holes using a center punch.
Repeat the process for the second profile; the template is no longer needed after this step.
Next, carefully drill pilot holes using small drill bits, then enlarge them to 6 mm and 8 mm respectively from both sides using a step drill bit. The center hole only needs to be enlarged enough for the 2.5 mm hex key to pass through without binding.
Be sure to deburr the hole; risk of injury!
Install an M3x35 screw in each carriage, using the largest possible washer to prevent the screw head from digging into the material.
Secure the carriages using two M5x10 countersunk screws each, then reassemble the profiles.
The roller brackets are designed to accommodate M3 heat-set inserts installed from the bracket side.
Finally, mount the belts with the rollers and the original screws, then re-tension the belts.