Raspberry Pi Zero 2 W Case with Heatsink Window (Bolted Through, No Supports)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Bolted-through Raspberry Pi Zero 2 W case with heatsink window, port panels and optional closed cover. No supports.
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 17
- Wydruki
- 0
- Wyświetlenia
- 50
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
A compact two-part case for the Raspberry Pi Zero 2 W, held together by four M2.5 screws that run down through the lid, the board’s own mounting holes and the base into hex nuts sunk in the bottom. The board is clamped solid, with no clips to snap. A window in the roof leaves room for a 6 mm heatsink on the SoC. Vintage-inspired details, all cut into the surface. 70 x 35 x 16.54 mm.
Features
Two parts, base and lid, split at the PCB top, so the board drops straight into the base and every port opening is an open notch.
Four M2.5 socket head screws pass down through the lid posts, the Pi’s mounting holes and the base into captive hex nuts, so they clamp the board and close the case in one go.
Screw heads sit in counterbores in the roof; the nuts sit in hex pockets under the base, and the screw tips end flush with the nuts, so nothing sticks out.
Openings for every port:
mini HDMI, and both micro USBs (OTG, power) in one shared panel;
microSD, with a finger scoop;
CSI camera ribbon, sized for the connector’s latch;
each in a recessed panel with room for cable overmolds, and a chamfered lead-in on every opening.
Roof window for a heatsink up to the SoC’s size (15 x 15 mm), 6 mm tall: the heatsink sits just below the roof surface with its fins in open air.
GPIO slot in the roof that fits a 2x20 Dupont or ribbon socket, or a second cover with a solid roof when nothing plugs into the header.
Vent slots in the roof over the second chip.
Details cut into the surface: grip grooves across both halves on the back, an engraved roof band with cross grooves and three curved grooves running over the edge into the camera port, 45-degree chamfers on the bed edges and at the seam (a V-groove when closed).
Kaiju Labs claw mark on the roof and the full logo engraved underneath; unbranded versions of every part are included.
Print Settings
No supports needed. Print the base bottom-down and the lid roof-down, so the nut pockets and screw counterbores open onto the bed.
Chamfered bed edges and 45-degree groove ends keep everything self-supporting; the engraved details sit on bed faces.
Standard layer height (0.2 mm) works well. Print layout: 70 x 75 x 8.34 mm.
Hardware Needed
Raspberry Pi Zero 2 W
Heatsink for the SoC, up to 15 x 15 x 6 mm, on thermal tape (optional)
4 x M2.5 x 12 mm socket head cap screws (head up to 4.5 mm diameter; a standard M2.5 screw and nut kit has them)
4 x M2.5 hex nuts (5 mm across flats x 2 mm)
Assembly Notes
Push a nut into each hex pocket under the base.
Stick the heatsink on the SoC, seat the board on the base standoffs and put the lid on (the heatsink sits in the roof window).
From the top, drop each screw through its counterbore, the lid post, the board and the standoff, and tighten it into the nut.
Files
pi_zero_case_print.stl— base and lid laid out for printing (use this one)pi_zero_case_print.3mf— 3MF project with the print layout, opens in any slicer that reads 3MFpi_zero_case_base.stl— base on its ownpi_zero_case_lid.stl— lid on its own, in assembly orientation (roof up); flip it roof-down in the slicerpi_zero_case_lid_closed.stl— alternative lid with no GPIO opening, roof up like the lid; print it roof-down instead of the slotted lidpi_zero_case_print_nologo.stl,pi_zero_case_base_nologo.stl,pi_zero_case_lid_nologo.stl,pi_zero_case_lid_closed_nologo.stl— the same parts without the Kaiju Labs logo
Feel free to remix for your own board revision, ports or mounting!