1 / 1
Surface Mount Patress Box And Faceplate for RJ45 Keystone — zdjęcie 1

Surface Mount Patress Box And Faceplate for RJ45 Keystone

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Surface mount box and faceplate for ethernet keystone

Ocena
0 / 5
Polubienia
1
Pobrania
1
Wydruki
0
Wyświetlenia
31
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

DO NOT EMBED THIS PATTRESS IN YOUR WALL OR USE IT TO CONTAIN MAINS ELECTRICITY - THIS IS DESIGNED FOR NETWORK USE ONLY

# UK Single Gang Keystone Surface Box and Faceplates

A surface mounted 86 × 86 mm box for one RJ45 keystone, with a choice of plain or engraved faceplate. Both faceplates share the same mounting geometry and fit any of the box depths supplied here. The faceplate sits flush with the box outline; rear ribs strengthen it. The box has reinforced walls, two wall fixing holes, a rear cable hole, and closed cable entry panels on two opposite sides. Cut open only the side panel you need.

## Choose the files

Print one faceplate and one box. The faceplates are single-keystone-faceplate-plain.stl and single-keystone-faceplate-decorated.stl; the decorated version has engraved CAT6A and LAN 01 lettering. Box filenames give the depth in millimetres: 20, 30, 40, 50, 55, 60, 65 or 70. 55 mm is the starting choice for the jack used to develop this model.

The 20–40 mm boxes are for substantially shorter hardware: they cannot house the roughly 39.5 mm long jack used here. The 50 mm box has only about 10.5 mm nominal room beyond that jack, before its rear projections and cable bend. Check your terminated jack and cable route before choosing a shallow box.

## Keystone fit and hardware

The recessed clip opening is 14.8 × 19.3 mm with a 1.6 mm clip land. It was selected by physical PETG fit testing with one CAT6A keystone. Keystone clips and body lengths vary, so check your own jack before printing the full set. The jack is recessed to bring its front close to flush with the faceplate.

The two faceplate fixing centres are 60.3 mm apart. The box is designed for two non-flanged M3.5 heat-set inserts, approximately 5.2 mm outside diameter, in 4.8 mm pilot holes. Verify the insert you have before heating it in. Use suitable M3.5 faceplate screws; short boxes may need shorter screws. The rear wall has two 5 mm fixing holes on 58 mm vertical centres for mounting the box to the wall. Choose wall screws and anchors for the surface.

## Printing and assembly

- PETG is the material used for the fit test. A 0.4 mm nozzle and around 0.2 mm layers are reasonable starting settings; check narrow engraved lines in the slicer.

- Print the faceplate front face down. The decorative lettering is mirrored in the CAD so it reads normally on the finished front. Print the box flat back down, open mouth up.

- No support is intended for either part. A brim can help if your printer tends to lift tall box walls. Use enough perimeters to keep the walls and screw towers strong.

- Both side cable panels are closed as printed. Follow the outside groove with a sharp knife to cut out one panel, then clean the edge. The remaining web is 0.6 mm thick and is intended to be cut, not snapped.

- Fit the inserts, mount the box through the rear holes, route the cable through the rear hole or a cut-open side panel, clip the jack into the faceplate, then screw the faceplate to the box.

The source/ folder contains editable FreeCAD files and the Python build scripts. The box depth is the named BoxDepth parameter in its spreadsheet. This is an Ethernet/data enclosure; it has not been assessed for mains electrical use.

Tagi