1 / 3
Volvo XC60 key fob shell — zdjęcie 1
1 / 3

Volvo XC60 key fob shell

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A two-part, screw-together replacement shell for the Volvo XC60 key fob. Prints flat with no supports in about 12 g.

Ocena
0 / 5
Polubienia
0
Pobrania
4
Wydruki
0
Wyświetlenia
48
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Description

Replacement shell for the Volvo XC60 key fob, made of two parts: a base tray and a flat top cover that are held together with four M3 screws and nuts in the corners. The cover has a small locating lip that drops into the base, so the two halves line up on their own during assembly.

Both parts print flat on the bed with no supports, and the whole set takes roughly 12 g of filament.

Tested with: 2022 Volvo XC60 key fob. Other model years may use the same fob, but they haven't been tested.

⚠ This is a one-way conversion. The original factory shell isn't designed to be opened – I had to break it to get the electronics out. Make sure you have a working spare key before you start.

Dimensions

  • Base: 63 × 34 × 9 mm

  • Top cover: 63 × 34 × 2 mm

  • Assembled: 63 × 34 × ~10.5 mm

  • Inner cavity: ~49 × 32 × 8 mm

Walls and floor are 1 mm. The corner holes are Ø3 mm through both parts.

What you need

  • 1 × Base

  • 1 × Top cover

  • 4 × M3 screws (about 14 mm long) + 4 × M3 nuts

  • Electrical tape (to hold the battery)

Assembly

  1. Open the original fob and remove the electronics. The factory shell has to be broken open – work carefully so you don't damage the circuit board.

  2. Place the circuit board in the base cavity.

  3. Secure the battery to the board with electrical tape. There's no battery holder in this version yet, so the tape keeps the coin cell in contact and stops it moving around.

  4. Place the top cover so the notched end sits over the slotted end of the base; the lip on the underside of the cover drops into the cavity.

  5. Push the four M3 screws through the corner holes from the cover side, fit a nut on the underside of each, and tighten gently. The walls are 1 mm, so don't overtighten.

Print settings

  • Material: PLA (PETG optional)

  • Layer height: 0.16 mm (0.12 mm for a finer finish)

  • Wall generator: Arachne

  • Walls: 3 (the 1 mm walls print fully solid)

  • Top / bottom layers: 6 / 6

  • Infill: 15 % gyroid

  • X-Y hole compensation: 0.1–0.15 mm (so the M3 screws pass through)

  • Supports: None

  • Brim: None (mouse ears if the corners lift)

  • Plate: Textured PEI

  • Orientation: Both parts flat, as supplied in the files

PLA: nozzle 220 °C, bed 55–60 °C, part cooling fan 100 %
PETG: nozzle 240 °C, bed 70 °C, part cooling fan 30–40 %

Filament use: ~12 g total (≈ 7.5 g base + ≈ 5 g cover).

Known limitations / ideas for remixes

  • No built-in battery holder – the battery is held in with electrical tape for now. A proper battery clip or pocket would be the most useful improvement.

  • Only tested with a 2022 XC60 fob.

Remixes and improvements are very welcome – please share them back!

Tagi