Flip-Through Card Storage Crate for Yoto Cards (2 or 3 Lanes)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Open crate for Yoto cards: cards lean back so kids see the covers and flip through ~40 per lane in place.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 9
- Wydruki
- 0
- Wyświetlenia
- 37
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Organizers
- Licencja
- Creative Commons — Attribution — Noncommercial
An open, one-piece crate sized for Yoto audio-player cards (credit-card size according to third-party sources, 85.6 x 54 mm; check one of your cards). The cards stand in 2 or 3 lanes and lean back 12° against an inclined back wall, behind a low front lip, so the picture on the front card of each lane faces the child. To find a card, tip the front cards forward onto the lip to see the next cover, like flipping through records, then stand them back up. There is floor space in front of about 40 cards per lane for that. Optional flat index dividers separate stories, music, sleep and so on.
Validation status (please read): digitally validated only, with CAD geometry and card-fit checks, slicer checks without supports, and stability calculations on the CAD model. It has not been physically printed and has not been tried with real Yoto cards yet. All pictures are 3D renders of the CAD model (some with plain proxy cards, one a cut-away with the front wall removed; the upright box in the comparison picture is a generic illustration, not a real product), except the "How it works" side section and the dimension sheet, which are drawings generated from the model. None is a photograph.
Placement (required)
In short: stick the base down at all four corners with removable adhesive putty or mounting pads (recommended); a wall behind it only stops backward tipping.
The crate is light (about 78 g), so a child's push can tip it. Calculated on the CAD model, a free-standing 2-lane crate tips with a horizontal push at the top of the cards of:
backwards: about 0.4 N with one card per lane, rising to about 1.3 to 1.8 N when full (0.4 N is roughly the weight of 40 g; 3 lanes: about 0.6 N rising to 1.9 to 2.7 N). Pushing the cards back after browsing easily exceeds this.
sideways: about 0.5 N with one card per lane, up to about 3.2 N when full;
forwards, pushing a tipped fan of cards: about 1.5 N with few cards, up to about 4.3 N with both lanes full and tipped.
What helps:
Fix it down with removable adhesive putty or removable mounting pads under BOTH the front corners of the base and the back corners (the crate tips about an edge, so the pads must be on the side that lifts). This is the only listed option meant to resist tipping in every direction (not tried on a printed crate). Recommended.
Standing it with its back against a wall or a heavy object stops it tipping backwards only (the common case).
An anti-slip mat alone does NOT stop tipping: it only stops sliding.
Why
Families collect dozens of Yoto cards, and children pick them by the picture, often before they can read. One parent review describes the usual drawbacks: with a pouch it is hard to choose by sight, so the cards all come out; cards on improvised racks slip sideways; binders mean flicking page by page. Many of the card boxes we checked stand the cards upright or under a lid, so only the tops show. Open lean-back holders and slot stands exist too; this crate gives each group of cards its own lane of about 40, with the floor in front of the stack left free, so a full lane can be flipped through in place.
Features
Browse in place: tip the front cards forward onto the lip to see the next cover (deep in a lane you see its upper part), then stand them back up. No taking cards out.
The child sees the covers: about 70 % of the front card's height shows above the 25.5 mm lip.
2 or 3 lanes side by side, so a collection can be grouped, with optional dividers.
Cards cannot fall sideways: each lane is only 1.6 mm wider than a card.
The flat base reaches 46.5 mm in front of the lip, under tipped cards and dividers, so pressing straight down on them does not tip the crate forward (calculated on the CAD model for every fill level; not tried with real cards). Pushing the cards backwards, sideways or forwards CAN tip a free-standing crate: see Placement.
One support-free part per crate: no hardware, glue or assembly (you will need removable adhesive putty or mounting pads to fix it down, see Placement). Rounded edges and corners.
Which file?
File | What | W x D x H (mm) | Est. time: Prusa MK4S (HF 0.4 nozzle, 0.20mm SPEED preset with 3 perimeters) / slow generic profile | Est. PETG |
|---|---|---|---|---|
card-crate_2-lanes | 2 lanes x about 40 cards (default) | 121.2 x 127.7 x 61.5 | 1 h 41 min / 5 h 37 min | 78.0 g |
card-crate_3-lanes | 3 lanes x about 40 cards (needs a bed of about 190 mm) | 178.7 x 127.7 x 61.5 | 2 h 27 min / 8 h 17 min | 113.1 g |
divider_middle-tab | index divider, tab in the middle | 52.98 x 97.6 x 2.0 | 15 min / 44 min | 10.7 g |
divider_side-tab | index divider, tab at the side (turn it over for the other side) | 52.98 x 97.6 x 2.0 | 15 min / 44 min | 10.7 g |
card-crate_2-lanes_with-2-dividers_plate (3MF) | the 2-lane crate and both dividers laid out on one plate; geometry only (no print settings); needs a bed of about 240 mm (on smaller beds use Arrange or print the separate files) | 237.1 x 127.7 x 61.5 (plate) | - | - |
Filament figures are for the MK4S reference slice (the generic profile gives 81.3 g, 118.1 g and 11.7 g). Slicer estimates, not measured prints. Each divider takes the place of about 3 cards; a piece of stiff card cut to size does the same job. All parts come as STL and STEP.
Dimensions and fit
Lane inner width 55.58 mm (card 53.98 mm + 0.8 mm per side); front lip 25.5 mm above the floor; back wall leaning 12°, its top 61.5 mm above the table; walls and base 2.0 mm; base apron 46.5 mm in front of the lip.
In use the leaned cards stand about 86 mm above the table, a divider tab about 98 mm. To lift a card out of a full lane you need about 14 cm of free height above the shelf (about 12 cm at the front of a lane).
Yoto cards are credit-card size (ISO/IEC 7810 ID-1, 85.60 x 53.98 mm, portrait artwork) according to third-party sources; no official Yoto statement was found. Check one of your cards.
Print settings
Material: PETG recommended (tough; less likely to crack if dropped or knocked). PLA also slices without supports but is more brittle: a PLA crate can crack into sharp pieces if dropped or stepped on. Check any print now and then and reprint a cracked one. Dividers: PETG.
Nozzle / layers: 0.4 mm nozzle, 0.20 mm layers, 3 perimeters, 15 % infill.
Supports: none (sliced with supports disabled: no floating islands, no bridged overhangs; like any solid plate, the base has one bridged infill layer inside it).
Orientation: as exported, crate standing on its flat base, open top up; dividers flat.
Bed adhesion: the first layer is a large solid plate (about 121 x 128 mm for 2 lanes). Clean the sheet; for PETG on a smooth PEI sheet use the usual separator (glue stick or similar); add a brim only if your printer tends to lift corners. Let the sheet cool, then flex it to release the part.
Strings: enable "avoid crossing perimeters" or good retraction to limit PETG strings across the open lanes.
Colours: a light, plain crate colour keeps the card pictures in front; printing the dividers in different colours helps children who cannot read yet (or put a picture sticker on the tab).
Use
No assembly. Fix it down or place it as described under Placement. Stand the cards in the lanes picture-side forward; they lean back against the back wall. To browse, tip the front cards forward onto the lip to see the next cover; stand them back up when done. A divider stands in the lane like a card, with its tab above the cards.
Limitations
Digitally validated only: not physically printed and not tried with real Yoto cards yet.
Capacity (about 40 per lane) is a browsing limit calculated with an assumed 0.95 mm per card (a card of about 0.8 mm plus about 0.15 mm of loose-stacking room); the real thickness of Yoto cards was not found. Check yours: stack 10 cards; if the stack is thicker than about 8 mm, fewer than 40 fit per lane (the source file can size a crate for your thickness). Labelled cards and dividers reduce capacity.
How far the next cover opens while browsing depends on how the cards sit: in the model's simulation about 42° with evenly spaced cards, about 24° with cards touching face to face.
Needs fixing down with removable adhesive putty/pads, or at least a wall behind it; an anti-slip mat alone does not stop it tipping.
Open storage: keeps cards upright and visible, not protected from dust or spills.
Print quality depends on the printer: the 0.6 mm edge rounding in the CAD will show as small layer steps, and the top of the back wall ends in a narrow crest one or two lines wide.
It is a storage accessory, not a toy, and makes no child-safety claim.
Customize
The included model.py is the parametric CadQuery source with a small command-line exporter (no online customizer): python model.py --lanes 2 --cards 40 --card-t 0.80 --out crate.stl, where --card-t is the thickness of your cards (stack 10, measure, divide by 10). You can change lanes (1-3), cards per lane, card thickness, lean and lip height. validate() rejects many impossible or never-built values, but not every combination; a changed crate is not checked, and only credit-card-size cards were ever built. Keep cards per lane between about 20 and 60 (calculated limits for the lip height and for reaching the lip when tipping). A 1-lane crate can be exported but tips sideways very easily (about 0.14 N with one card, calculated), so it is not offered as a ready file. A divider corner radius of 5 mm fails to build with some tab sizes; 1-4 mm builds with every tab size tried. Comments in model.py refer to internal design documents that are not part of this upload, and one internal QA note there still mentions an anti-slip pad; that note is outdated: the Placement section above is what applies.
Pictures
3D renders of the uploaded files, some with plain proxy cards (simple sun and star shapes stand in for card art); the comparison picture sets a generic upright box (an illustration, not a specific product) next to the crate; one picture is a cut-away with the front wall removed to show the cards (red = cut faces, not part of the product's look); the "How it works" side section and the dimension sheet are drawings generated from the model.
Not affiliated with or endorsed by Yoto; Yoto is a trademark of its owner. The name is used only to say which cards the crate is sized for.