1 / 3
Digital Crazy Hours and Minutes (3 motors remix) — zdjęcie 1
1 / 3

Digital Crazy Hours and Minutes (3 motors remix)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Remix of the original model with a motor per rotor

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
21
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Wall-mounted
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

(Mirroring a remix I published on TG during 2023)

As a foreword, thanks to Shiura for this amazing design that inspired the community

This remix modifies the crazy clock in order to handle 3 motors, one per time rotor

The aim of this modification is twofold:

+ Avoid the zero detection system, which (in my case) never worked fluently

+ Limit drastically the noise generated during the moves

As a secondary effect, the modification shortens the time necessary for each move

The remix still use the M5stamp C3/C3U (tested only with C3U)

Controlling 3 motors has some impact:

+ Logging through usb is no longer possible (the clock supports logging through telnet, when USE_TELNET is defined)

+ Uploading sketch needs to put the C3U in download mode explicitly (button pressed while powering (I don't know if this applies also to the C3, probably not)

This is consequent to the use of the UART and USB pins as output to control the third motor

The whole set of parts is suitable for printing on a 220x220 bed

(Note that NS means No Support, SUP means standard support and ARB arborescent support)

The rear part is made compatible by clipping the corner

The frame is cut into two parts

Supporting shall be used for printing these parts

Overhang shall be sanded after print before fixing both parts together to obtain a continuity of the surfaces after gluing

All rotors have a numbering scheme different from the original

The hour rotor has been cut in 3 parts that shall be glued together (cyanoacrylate glue). Two versions are provided:

+ The "complex" one needs to be printed with standard support (not arborescent), and also sanding overhang to obtain a good continuity of the surfaces (sanding the interior of the included guide may help also). This is the version I printed for building my clock.

+ The "simple" version eliminates overhang (no need of sanding) and don't require support. However, altough this version has been checked carefully under slicer, I didn't print it (if someone print it, please let a comment on the result).

In any case, remove the purge line quickly to avoid merging it with the printed part.

The 10 minutes rotor shall be printed with arborescent support touching the plate

The 10 minutes rotor need to be fixed on the motor axis as tight as possible

As far as possible, the "very-tight" version should be used

However, to avoid printing for nothing, it is possible to print the test-axis and check in order to select the more appropriate version for your motor

A remix of the gear with less clearance and (hoping) less friction is also included

It is recommended to print these gears with maximum quality

Note that:

+ The idler gear of the original model is now replaced by an active gear (similar to the hour gear) on the third motor (minute)

+ The other gear of the original model may also be reused

Lubricate rack and gear, as well as axis, with silicon based oil

The position of the M5stamp has been changed to accommodates the third motor

The third control board now resides where the M5stamp was before (sorry, but fixation holes are not provided), and the M5stamp is now central (the cable exit also, that's a benefit)

Be careful to avoid using too long screws for the central box fixation, since the frame is rather thin at this place

The box screw needs to be at least 5mm long plus the length of screwing (ex: 8mm to have a screwing length of 3 mm)

Part named "-Opt" (Digits and rings, optional) permit to print numbers and rings in different colors (as in the picture)

The connexion between the C3 and the motors are as Following:

+ First motor (hour) : 7, 6, 5, 4 (to be changed in 4, 5, 6, 7 if going wrong side, but if connected as in the picture, it should not)

+ Second motor (10 minutes) : 10, 8, 1, 0 (to be changed to 0, 1, 8, 10 if going wrong side)

+ Third motor (minutes) : 21, 9, 18, 19 ( to be changed to 19, 18, 9, 21 if going wrong side)

The software is contained in the CZC.zip archive

Instructions for compiling the software are given in the CZC-clock-howto.pdf document

Additional information is available at the beginning of Net_strategy.h

In order to permit uploading on C3U without opening the box, it may be useful to connect a push button between the pin 9 (also connected to the third motor) and the ground

(Pin 9 correspond to the button on the C3U itself)

It seems that this is not necessary with C3 (since it has a dedicated chip for serial downloading)

Demonstration video : ?share=copy