1 / 8
weBoost Office 100 Panel Antenna Angled Wall Mount — zdjęcie 1
1 / 8

weBoost Office 100 Panel Antenna Angled Wall Mount

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

45° angle & 9° tilt directional wall mount bracket for weBoost Office 100 internal panel antenna.

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
12
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This wall-mount bracket was designed for the weBoost Office 100 internal wall-mount panel antenna.

The goal was to position the panel near a room corner while aiming it across the room rather than directly perpendicular to the wall. The bracket holds the antenna at a 45° horizontal angle from the mounting wall and adds a 9° downward tilt.

It also keeps the antenna close to the adjoining wall, allowing the panel to sit approximately 15 mm away from the corner wall.

This is an AI-assisted original design that I refined around the dimensions and mounting requirements of the weBoost panel.

Design Features

  • Designed for the weBoost Office 100 internal panel antenna

  • 45° horizontal angle from the mounting wall

  • 9° downward tilt

  • Positions the antenna approximately 15 mm from the adjoining wall

  • Reinforced support arms between the wall plate and antenna mounting plate

  • Elongated wall-mount slots provide some flexibility when positioning the bracket

  • Uses the existing metal antenna mounting plate

  • Localized higher infill is used around major connection points for additional strength

The weBoost panel itself is approximately:

  • Just under 170 mm tall

  • Just under 160 mm wide

The factory mounting plate attaches to the printed bracket using M4 screws.

For mounting the bracket to the wall, use fasteners appropriate for the wall construction and expected load.

Installation

  1. Mount the printed bracket to the wall using the four elongated mounting slots.

  2. Attach the weBoost metal mounting plate to the front of the bracket using M4 screws.

  3. Attach the antenna to its mounting plate normally.

  4. Position the bracket near the corner so the antenna maintains approximately 15 mm of clearance from the adjoining wall.

The finished installation directs the face of the antenna diagonally into the room while the 9° downward angle helps aim the signal toward the occupied area below the mounting height.

Technical Recommendations

The pictured bracket was printed in Elegoo Rapid PETG, and PETG is a good material choice for this design because the bracket remains under continuous mechanical load after installation.

The model uses 20% gyroid infill for the majority of the print, with 35% localized infill modifiers around the structural connection points. These areas were intentionally reinforced because they transfer load between the wall plate, support arms, and antenna mounting plate.

Three wall loops were used for the printed version.

PLA should also be suitable for many indoor installations where temperatures remain moderate, but PETG is preferable where additional toughness and long-term load resistance are desired.

ABS or ASA could also be used, although they are not necessary for a typical indoor installation unless the bracket will be exposed to unusually high temperatures.

The supplied print was oriented with the wall-mount plate flat on the print bed, as shown in the slicer screenshots. Tree supports were used to support the elevated portions of the antenna mounting structure.

Print Settings Summary

  • Printer Used: Creality K1 Max

  • Layer Height: 0.20 mm

  • Nozzle Diameter: 0.4 mm

  • Material Used: PETG

  • Material / Filament Brand: Elegoo Rapid PETG

  • Color: Black

  • Wall Loops / Perimeters: 3

  • Base Infill: 20%

  • Infill Pattern: Gyroid

  • Infill Modifiers: 35% localized infill at structural connection points

  • Supports: Yes — Tree (Auto)

  • Print Time: 3h 28m 29s

  • Filament Weight: 89.27 g

  • Print Orientation: Wall-mount plate flat on the build plate

  • Brim / Raft: None

Tagi