Ergonomic Stand + Wrist Rest for Logitech MX Mechanical – Adjustable Tilt, TPU Cushions & Hidden Magnetic Storage
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A one-piece keyboard deck and cushioned wrist rest for the MX Mechanical, with two typing angles and magnetic storage un
- Ocena
- 0 / 5
- Polubienia
- 11
- Pobrania
- 12
- Wydruki
- 0
- Wyświetlenia
- 170
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Computers
- Licencja
- Creative Commons — Public Domain
Ergonomic Keyboard Stand + Wrist Rest for Logitech MX Mechanical
A sculpted keyboard deck and a cushioned wrist rest in one unit. The keyboard and your palms stay aligned, your wrists rest on soft TPU instead of a hard desk edge, and two magnetic caps hide storage for a receiver, cables or small tools.
Why it helps (accessibility)
Typing on a flat desk often means bent-back wrists and pressure on the edge of the table. This stand is meant for anyone who types for long hours, and especially people managing wrist discomfort, RSI or reduced hand strength:
Less wrist extension: the wedge deck and matching palm rest keep your hands closer to neutral.
Softer contact: flexible TPU cushions spread pressure where your wrists land.
Two typing angles: seat the keyboard in either position for a 3° change in tilt, with no tools.
Easy access: the storage caps are held by magnets and lift off without any force or fiddly latches.
Non-destructive: the keyboard simply sits in the deck. Nothing is drilled, opened or modified.
Features
Footprint: 435 × 268 × 33 mm (W × D × H)
Two TPU wrist cushions
2 magnetic caps covering hidden storage boxes (24 × Ø5 × 2 mm magnets)
Two keyboard positions, 3° apart
Base as one piece or as four sections for smaller printers
Choose your base
OnePiece: print Base_OnePiece (needs a 435 × 268 mm bed).
Split: print the four Base_Split_… sections, plus the tenons and screws below.
Printed parts
File | Qty | Material |
|---|---|---|
Base: OnePiece or 4 × Split sections | 1 / 4 | PLA or PETG |
Tenon 4 × 14 × 20 mm (split only) | 4 | PLA or PETG |
Tenon 3 × 12 × 16 mm, bottom joint (split only) | 1 | PLA or PETG |
Cap, left and right | 1 each | PLA or PETG |
Cushion, left and right | 1 each | TPU |
Non-printed hardware
24 × round magnet, Ø5 × 2 mm: [purchase link]
4 × self-tapping screw ST2.9 × 13 mm (split base only): [purchase link]
2 × self-tapping screw ST4.2 × 25 mm (split base only): [purchase link]
Assembly
(Split base) Press the five tenons into the slots and push the four sections together. The small 3 × 12 × 16 mm tenon goes in the bottom joint.
(Split base) Flip the base over and drive the self-tapping screws from the underside: 2 × ST4.2 × 25 and 4 × ST2.9 × 13.
Press the magnets into the pockets in the caps and storage boxes. Check polarity so each cap attracts rather than repels, and add a drop of CA glue if the fit is loose.
Glue each TPU cushion onto its cap. Lightly sand the cap's top surface, apply a thin, even layer of glue (flexible CA glue or contact adhesive bonds TPU well), press the cushion down, and let it cure fully before use.
Set the caps in place, place your MX Mechanical in the deck in Option 1 (steeper) or Option 2 (3° flatter), and you're done.