Balancing Falcon on a Perch - Stays Up on Its Beak Tip (Low-Poly, No Supports)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A low-poly falcon that balances on its beak tip. Push it and it rights itself: 2 hidden M8 nuts. No supports.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 17
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
A falcon that balances on the tip of its beak. Nudge it, spin it, blow on it: it wobbles and always comes back level. Low-poly faceted body, feathered wings with engraved primaries, and a hexagonal desert-rock perch.
Why it stays up
The head is raised on a long neck and the wing tips sweep forward and curl down, each with a hidden M8 nut. That puts the centre of mass 11 mm below the beak, so gravity always pulls it back upright.
I did not guess this: the balance was computed in CAD from the real part volumes, using the gram weights Bambu Studio gives for the included print profiles and the weight of a standard M8 nut. With the included 3MF files it rests between 0° and 10° nose-up, and the centre of mass stays about 11 mm below the pivot.
A small cone under the beak seats on the needle tip of the perch, so it spins freely without sliding off. In CAD the falcon clears the perch from 10° nose-down to 35° nose-up and ±20° of roll.
Parts (PLA, 0.2 mm, no supports)
Body, printed on its side: 19 min, 8 g.
Wings (one piece, 173 mm span, fits the A1 mini), printed top face down: 36 min, 20 g.
Perch: 38 min, 20 g.
Also needed: two M8 hex nuts (standard DIN 934, 13 mm across flats), pressed into the pockets under the wing tips.
Use the included 3MF files or the same settings: 15% infill, 2 walls. Printed solid, the body is heavier: the falcon tips about 40° nose-up and its throat leans on the post. If that happens, a pea-sized piece of blu-tack under each wing tip brings it back level.
Assembly
Press an M8 nut into the pocket under each wing tip.
Drop the wings into the slot on the back of the body. Gravity holds them; add a drop of glue if you want.
Set the beak on the perch tip and let go.
Parametric source included (build123d / Python): wing sweep, span, neck height and nut size are variables, and the script prints the new balance angle.
About this design
Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders, not photos. Not printed yet: makes and feedback are very welcome.
Español
Halcón que se sostiene sobre la punta del pico en su percha: lo empujas y siempre vuelve. Dos tuercas M8 escondidas en las puntas de las alas bajan el centro de masas 11 mm por debajo del pico. Sin soportes, cabe en el A1 mini.
العربية
صقر يتوازن على طرف منقاره فوق مجثمه، مهما دفعته يعود إلى مكانه. صامولتان M8 مخفيتان في طرفي الجناحين تجعلان مركز الثقل تحت المنقار.