Tea Ceremony Hand-Crank Automaton: Teapot Pours, Cookie Plate Turns (Multicolor)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Turn the crank: the teapot tilts and pours a blue stream into the glass, cookie plate turns on bevel gears. No supports.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 16
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Toys & Games
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
The GIF above is an animation of the real movement: 36 frames rendered from the same 36 crank positions that the collision test checks.
The Tea Ceremony, a hand-crank automaton. Turn the crank and a Moroccan-style teapot tilts 45° and pours into a tea glass: a blue stream rises out of the glass and reaches the spout, holds for a moment, sinks back, and the teapot returns. At the same time a plate with seven little cookies turns slowly on a pair of bevel gears. Everything works with cams and gears that you can watch through the front window and the see-through lattice at the back.
How it works
One hexagonal camshaft (7 mm) carries two cams. Each cam lifts a square follower rod (6 mm) with a rounded tip. The rods slide in 6.6 mm square guides (0.3 mm clearance on each side) and fall back by gravity.
Teapot cam: the rod pushes the underside of the teapot 14 mm behind its pivot. The rod rises 14.0 mm, so the teapot tilts from 0° to 45°. It tilts between 20° and 95° of the crank, holds until 265°, and is back at 340°.
Stream cam: the blue stream rises 16.7 mm between 100° and 180°, holds until 190°, and is hidden again by 255°. It only comes out while the teapot is fully tilted.
The glass sits exactly where the spout ends up: the spout opening was calculated to be over the glass axis when pouring (x = 13.2 mm), 18.2 mm above the rim. The stream stops 1.05 mm below the spout, so it looks like the tea comes out of it.
Bevel gears, module 1.5, 14:28: one crank turn moves the plate half a turn. With 6 cookies at 60°, the motion loops cleanly.
The cams use smooth (harmonic) motion with rests. Maximum pressure angle: 27.6° (teapot) and 31.0° (stream).
Details
Size assembled: 190 × 88 × 191 mm (with crank). Box 156 × 88 × 102 mm.
Front panel printed face down with flush 0.6 mm inlays: a band of 8-point geometric stars in blue and terracotta, a gold frame around the window, and a small gold HANMA.
Stage with a tile-style checkerboard border in blue and terracotta. Back wall: see-through diamond lattice (45° edges, prints upright without supports). Side walls: V-groove lattice. Turned crank knob.
Teapot: bulb with raised rings, flared neck, tall faceted lid with ball finial, long curved spout with lip and open mouth, side handle with thumb rest. Printed in two halves joined with 3 printed pins.
Tea glass in terracotta with two gold bands (colour change by layer) and cut facets. Plate with gold rim, inlaid ring, and 6 ridged terracotta cookies around 1 gold one. Fluted blue stand with a small tray.
All parts print without supports. Horizontal holes are teardrops, blind holes have pointed tops, the bevel gear and its hub are separate so both print flat.
Print (Bambu A1 mini + AMS lite)
6 plates, 15 h 33 min and 313 g in total (Bambu Studio estimate): cream 192 g, blue 27 g, terracotta 45 g, gold 49 g.
1 Box (cream): 3 h 52 min, 109 g. 2 Front (4 colours): 0 h 57 min, 22 g. 3 Stage (3 colours): 1 h 28 min, 46 g. 4 Scene: teapot halves, stand, glass, plate, gear hub (3 colours): 5 h 54 min, 78 g. 5 Shafts, rods and 20 pins: 1 h 19 min, 24 g. 6 Cams, gears and crank: 2 h 00 min, 33 g.
Colours: cream #EFE4CC, blue #1F4E8C, terracotta #B5523B, gold #C9A13B. PLA, 0.2 mm layers.
Assembly
Pin the front panel to the box (4 pins, 10 mm).
Slide the camshaft in from the left. On the way, slide on the teapot cam, the stream cam and the small bevel gear (the hub of each cam faces the crank). Add the collar on the left and the crank on the right.
Pass the plate shaft down through the stage (its flange rests on top). Pin the large bevel gear to its hub (3 pins) and push it onto the shaft from below, hub up, until the hub touches the guide under the stage, then back it off about 0.4 mm so it turns freely (the guide then stops it from climbing out of mesh). Push the plate onto the top of the shaft. The gear and the plate are press fits on the hexagon: add a drop of glue if they feel loose.
Drop the two rods through the stage guides, pin the stand and the glass to the stage (2 + 2 pins), join the teapot halves (3 pins) and hang the teapot on the stand with the hexagonal pivot pin.
Pin the stage onto the box (6 pins). Turn the crank either way.
How it was checked
Full 360° cycle in 36 positions (every 10°): no moving part touches the box, front, stage, stand, glass or pivot pin, and no moving part touches another (0.0000 mm³ intersection in every position).
The followers really ride on their cams and the teapot really rests on its rod: 0 mm³ overlap, but moved 0.2 mm further in they collide in all 36 positions (at least 1.0 mm³).
Real clearances: rods in guides 0.30 mm, camshaft in its bearings 0.35 mm, teapot on its pivot pin 0.22 mm, teapot to stand and glass 0.40 mm, gear teeth 0.16 mm, plate shaft 0.23 mm.
Controls that must fail: the large gear turned half a tooth collides (36.7 mm³); the large gear 0.6 mm lower touches (the gears really mesh); a rod moved 0.35 mm sideways hits its guide; the teapot 4° less tilted than its rod allows goes through it; the stream 3.7 mm higher goes into the spout; at 10° of tilt the spout is 13.6 mm off the glass; with the stream timing moved 30° earlier it would come out before the teapot tilts; with double the stream lift the pressure angle would reach 47°.
Printability: overhangs over 45° on every plate 0 to 1.7 mm², 0 floating parts, no colour overlaps, every plate fits the 175 × 175 mm bed.
About this design
Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.
Español
El GIF es una animación del movimiento real. Autómata de manivela «La ceremonia del té»: al girar la manivela, una tetera de estilo marroquí se inclina 45° y sirve en un vaso (un chorro azul sube del vaso hasta el pico), vuelve, y a la vez un plato con dulces gira despacio con engranajes cónicos 14:28. Levas y seguidores a la vista por una ventana. 4 colores, sin soportes, 6 placas para la A1 mini: 15 h 33 min y 313 g. Comprobado en 36 posiciones sin choques.
العربية
الصورة المتحركة تظهر الحركة الحقيقية. دمية آلية بذراع تدوير اسمها «حفل الشاي»: عندما تدير الذراع، يميل إبريق شاي بطراز مغربي 45 درجة ويصب في كأس (يرتفع خيط أزرق من الكأس حتى فم الإبريق)، ثم يعود. وفي الوقت نفسه يدور طبق الحلويات ببطء بواسطة تروس مخروطية 14:28. الكامات والتوابع ظاهرة من خلال نافذة. 4 ألوان، بدون دعامات، 6 ألواح لطابعة A1 mini: 15 ساعة و33 دقيقة و313 غراما. تم التحقق من 36 وضعا بدون أي تصادم.