1 / 4
Peonza: Japanese Spinning Top with Rack Launcher (optical colour face, multicolor) — zdjęcie 1
1 / 4

Peonza: Japanese Spinning Top with Rack Launcher (optical colour face, multicolor)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Pull the rack: a ratchet pinion spins this koma to ~3000 rpm and its 4-colour face melts into rings. No supports.

Ocena
0 / 5
Polubienia
1
Pobrania
3
Wydruki
0
Wyświetlenia
24
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

The animation (GIF) shows the real motion, rendered from the same 36 positions that were collision-checked in code. The spin blur is real too: each fast frame is the average of up to 16 renders of the top across the angle it turns during the exposure.

Peonza is a Japanese-style spinning top (koma) with a rack launcher. Stand the top on the table, set the launcher on it, and pull the toothed rack out in one quick stroke. A 10-tooth pinion spins the top through a one-way ratchet: 2.8 turns per pull and about 3,000 rpm with a normal 2 m/s pull. When the rack runs out, the top is faster than the pinion, the ratchet slips and you lift the launcher away.

Optical face

  • The top face carries a geometric pattern in four colours, inlaid flush: 16 asanoha-style triangles in alternating gold and coral, five cream log-spirals, and three tracks of arcs at 12, 6 and 24 repeats (a Maxwell / Benham disc idea).

  • At speed each track melts into a solid ring of a blended colour. As the top slows down the spirals seem to crawl and the arc tracks flicker and strobe at different rates.

  • The side has edo-goma style stripes (gold, coral, cream, and a gold ring on the cone) between turned V-grooves, like a lathe-turned wooden koma.

Mechanism

  • Rack and pinion: module 1.25, 20° pressure angle, real involute teeth. The pinion has 10 teeth with +0.4 profile shift (no undercut) and is cut in code by a rolling rack, so the flanks are true conjugates. The rack has 110 mm of teeth plus a ring handle.

  • One-way ratchet: six sawtooth teeth (1.5 mm high) on the pinion hub sit on six matching teeth on the axle crown. The drive faces are vertical and the backs are 30° ramps, so it drives in the pull direction and clicks past the other way, also when you push the rack back in.

  • A 4.8 mm pivot on the crown slides into the pinion bore and keeps the top centred under the launcher.

  • Top: Ø56 mm body with a heavy rim, hex axle (6 mm across flats) with a 45° seating cone that centres the body, and a push-fit tip held by three 0.15 mm crush ribs. Two tips are included: fine (Ø1.6 ball, long quiet spin) and round (Ø6 ball, wanders around the table).

  • Size: the top is Ø56 × 32.5 mm. The launcher is 54 × 87 × 11.4 mm, and the rack is 167 mm long.

Print

  • A1 mini + AMS lite, 4 colours: navy #1f3263, gold #e3a82b, coral #ea5f3c, cream #f4ead6. Two 3MF files, both print-ready with colours assigned, no supports.

  • Plate 1, the top body: the pattern face goes down on the bed, so the colours are only in the first 0.6 mm and the stripes are whole layers (few colour changes). It is sliced at 100% infill, because more mass in the rim spins longer and solid infill keeps it balanced. 1 h 05 min, 34.8 g.

  • Plate 2: launcher base, cover (inlaid HANMA, sun and pull arrow), pinion, rack, axle and both tips. 1 h 19 min, 31.8 g.

  • Assembly: push the axle through the body from the pattern side until the cone seats, then press a tip onto the peg underneath. Put the pinion into the base (the hub goes down through the floor), then press the cover on (3 pegs, a drop of glue is optional). Slide the rack in against the arrow, teeth first.

  • To launch: stand the top on a smooth hard table and lower the launcher so that the pivot enters the pinion. Press lightly, pull the ring fast along the arrow, then lift straight up.

  • Not a battle top. It is made for spinning and for watching the colours.

How it was checked

  • Rack and pinion at 24 positions along the whole engagement: 0.0000 mm³ collision, smallest gap 0.220 mm and largest 0.222 mm, so the teeth never jam and never lose mesh. Control: a module 1.5 rack against the same pinion collides (31 mm³).

  • Full cycle at the 36 GIF positions (pull, lift, reload, set down): no pair of parts collides, and every moving pair keeps at least 0.20 mm. Controls: zero backlash leaves a 0.000 mm gap, and a pinion half a tooth out of phase collides (27 mm³).

  • Ratchet: to turn 2° in the pull direction, the launcher would have to lift 0.99 mm, so the 84° wall locks and drives the top. In the other direction the 29.6° ramp lets it slip over a whole tooth. Control: the same ratchet built the other way round does not drive (0.00 mm lift).

  • Speed: 109.9 mm of engaged rack / 39.27 mm pinion circumference = 2.80 turns per pull. rpm = 60·v/(π·d): 1,528 rpm at 1 m/s, 3,056 at 2 m/s and 4,584 at 3 m/s. A 2 m/s launch stores 0.53 J, which takes an average pull of about 4.8 N.

  • Gyroscopic stability: Iz/Ix = 1.82 about the centre of mass (above the 1.2 target). The centre of mass is 18.8 mm above the tip (h/D = 0.34). The minimum sleeping-top speed is 583 rpm, far below the launch speed. Control: a tall, narrow top (Ø24 × 78 mm) fails with Iz/Ix 0.48 and h/D 1.92.

  • Balance: the centre of mass is 0.0 µm off the spin axis (target under 50 µm). Control: a body 0.3 mm off-centre gives 274 µm.

  • Printing: every part is one solid on the bed with 0.00 mm² of overhang over 45° (0.46 mm² on the tips' socket cone). Control: a flat disc under the axle cone gives 170 mm². The colours do not overlap, every inlay is at least 0.4 mm wide, and both plates fit 175 × 175 mm.

About this design

Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.

Español

GIF del movimiento real. Peonza japonesa (koma) con lanzador de cremallera. Tiras de la cremallera, un piñón de 10 dientes la hace girar a través de un trinquete de un solo sentido: 2,8 vueltas por tirón y unas 3.000 rpm. Su cara tiene un patrón geométrico de 4 colores que, al girar, se funde en anillos de color. La punta se cambia (fina o redonda). Sin soportes. Cuerpo: 1 h 05 min, 34.8 g. Lanzador: 1 h 19 min, 31.8 g.

العربية

صورة GIF للحركة الحقيقية. خذروف ياباني (كوما) مع قاذف بمسننة مستقيمة. اسحب المسننة فيديرها ترس من 10 أسنان عبر سقاطة تعمل في اتجاه واحد: 2.8 دورة في كل سحبة ونحو 3000 دورة في الدقيقة. على وجهها نقش هندسي بأربعة ألوان يذوب في حلقات ملونة عند الدوران. الرأس قابل للتبديل (رفيع أو مستدير). تطبع دون دعامات.

Tagi