1 / 4
Pecking Woodpecker Toy - stick-slip pole climber, print-in-place spring (multicolour) — zdjęcie 1
1 / 4

Pecking Woodpecker Toy - stick-slip pole climber, print-in-place spring (multicolour)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Classic woodpecker that pecks its way down a pole. Print-in-place spring, physics checked, GIF of the real motion.

Ocena
0 / 5
Polubienia
0
Pobrania
10
Wydruki
0
Wyświetlenia
29
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

The GIF is the real motion computed by the physics model (stick-slip with friction), rendered frame by frame: the classic woodpecker toy that pecks its way down a pole. Lift the bird to the top, tip its tail down a little and let go: it swings on its zigzag spring, the beak knocks on the pole about 9 times a second and it hops down 6.9 mm per peck, about 64 mm/s, until it lands on the thick part of the pole. Lift it up and it goes again.

How it works

The square ring around the pole is 0.35 mm looser on each side, so it can tilt 3.9°. When the bird's weight tilts it, two opposite inner edges bite into the pole and friction holds it (stick). Each swing of the bird straightens the ring for a moment and it slips down (slip), then it tilts and jams again while the beak hits the pole. It jams when h / 2L < μ: ring height h = 10 mm, bird's weight at L = 26.7 mm from the pole, so h/2L = 0.224, safely below μ = 0.30-0.40 for PLA on PLA. Picture 2 shows both states to scale.

Details

  • Size: 184 mm tall; stump Ø72 mm (about 111 mm across the roots and leaves); bird 10 mm thick, about 44 × 50 mm.

  • Great spotted woodpecker colours: black body with cream cheeks, shoulder patch and wing spots, red nape and red under the tail, eye with a cream ring and highlight, feather grooves on the wing and tail, rounded top edges.

  • The bird, its zigzag spring (0.9 mm leaf, 7 turns) and the ring are ONE print-in-place part, printed lying flat. The ring hole is 7.7 × 8.0 mm for the 7 × 7 mm pole.

  • Stump with bark grooves and root flares, cut face with growth rings and a crack, a red mushroom with cream dots, a leafy twig and a small HANMA inlaid on top. The pole has bark marks on its front face only (the ring slides on the side faces).

Printing

  • Bambu Studio, A1 mini + AMS lite, 0.2 mm layers, no supports. Two plates:

  • Plate 1, stump + pole: 2 h 10 min, 58 g (brown 45 g, green 3 g, cream 8 g, red 2 g). AMS: 1 brown, 2 green, 3 cream, 4 red.

  • Plate 2, bird + spring + ring: 0 h 40 min, 13 g (black 9 g, cream 3 g, red 1 g). AMS: 1 black, 2 cream, 3 red. Printed with 100% infill so its weight and balance match the physics model. Colours are only in the bottom and top 3 layers, so there are few colour changes.

  • Only overhang: the 7.7 mm bridge over the ring hole (prints fine as a bridge; the hole has 0.5 mm extra room on that side in case it sags).

  • Assembly: slide the ring onto the pole from the top, push the pole into the stump (0.15 mm per side, snug). Do not grease the pole: it needs friction.

  • Tuning: if it slides down in big jumps, the ring hole printed loose (reprint the bird with X-Y hole compensation -0.05 mm); if it barely moves, the ring is too tight: run it up and down a few times or lightly sand the pole sides.

How it was checked

  • Physics: a planar model of the ring (slide + tilt), the bird on its spring and the beak, with Coulomb friction (real sticking) and contacts, using the mass, centre of mass and inertia measured from the actual meshes (bird 8.2 g). It settles into a steady cycle: 106.9 ms per peck, 6.89 mm per peck (repeats to ±0.01 mm), ring at rest 42% of the time, exactly one beak hit per swing.

  • Spring: k = E·I/L = 20.4 N·mm/rad, estimated swing frequency √(k/J)/2π = 13.0 Hz; the simulated cycle is 9.4 Hz because of the free-fall moments and the beak hits. Peak strain in the PLA leaf 0.20%, and the zigzag turns stay 0.41 mm apart at the largest swing (23°).

  • Robustness: 81 combinations of friction (0.30-0.40), clearance (0.30-0.40 mm per side), PLA stiffness (2.3-3.5 GPa) and how hard you start it: all walk down pecking, 37-221 mm/s, never falling off.

  • Controls that must fail: ring 3× taller or a waxed pole (μ 0.15) never jam and drop down in one go; zero clearance can't tilt and barely creeps without pecking. Twice the clearance (or a thinner pole) still jams in this model but jumps ~41 mm at a time (248 mm/s), which is why the clearance is 0.35 mm.

  • With the real meshes at the 36 positions of the GIF: the ring only touches the pole at its two biting edges (worst overlap 0.0007 mm³), only the beak tip reaches the pole, the bird never touches the ring, and 15° further the beak would dig into the pole. At the bottom the tail stays at least 10.0 mm above the stump.

  • Print-in-place: one solid part on the bed, spring turns 1.0 mm apart and ≥ 0.95 mm from the ring and body, nothing floating; layer-by-layer 45° rule: nothing in the air except the ring-hole bridge. Colours never overlap; all inlays survive a 0.4 mm feature test.

About this design

Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.

Español

El clásico juguete del pájaro carpintero que baja picoteando por un poste: el anillo se inclina 3.9° y se traba por rozamiento (h/2L = 0.224 < μ), el muelle en zigzag lo hace oscilar, se suelta un instante, baja 6.9 mm y el pico golpea el poste unas 9 veces por segundo. Pájaro, muelle y anillo salen en una sola pieza impresa; tocón con corteza, hojas, seta y poste en otra placa. Sin soportes, AMS (5 colores en total, 4 por placa).

العربية

اللعبة الكلاسيكية لنقار الخشب الذي ينزل على العمود وهو ينقر: تميل الحلقة 3.9° فتنحشر بالاحتكاك، والنابض المتعرج يجعل الطائر يتأرجح فتنفلت الحلقة لحظة وتنزل 6.9 مم، ويضرب المنقار العمود نحو 9 مرات في الثانية. الطائر والنابض والحلقة قطعة واحدة مطبوعة، وجذع الشجرة بالأوراق والعمود في لوح آخر، بدون دعامات.

Tagi