Marking Template for StoreMax Handle Round (50 mm, sliding doors)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Hook-over marking jig that places both holes for the StoreMax "Handle Round" exactly 50 mm apart and 35 mm from the door
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 1
- Wydruki
- 1
- Wyświetlenia
- 19
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution
The StoreMax Handle Round (sold at DIY stores) mounts with two threaded bushings that sink into 7 mm holes in the door. The fit is tight: the bushings have to land exactly in those holes, so a 1 mm error in spacing or position is immediately visible. When you fit several sliding doors in a row you also want every handle at exactly the same spot.
This template takes care of that:
Fixed hole pitch of 50 mm, the centre-to-centre distance of the handle.
Lip that hooks over the door edge. The handle centre line always ends up 35 mm from the edge (first hole at 35 mm, second at 85 mm).
V-notch on the hole axis. Draw one pencil line where the handle should go (for example at half the door height), put the notch on the line and you're centred.
Ø2.5 mm through-holes for an awl or a sharp pencil. They give you a precise centre point for the drill.
Ø7.3 mm counterbores (2 mm deep) let you test-fit the handle's bushings on the template before you drill your door. They sit on the door side, so you won't see them while marking.
Works on doors from 15 to 19 mm thick. The lip only touches the edge, so the door can be thicker.
How to use
Draw a line on the door where the handle should go (e.g. at half the door height), running to the edge.
Hook the lip over the door edge and line the V-notch up with your pencil line.
Push an awl through both Ø2.5 mm holes to mark the centres.
Remove the template and drill both holes at Ø7 mm. A brad-point (wood) drill bit drops straight into the awl mark and won't wander.
Watch your depth. On a 15 mm door you're through before you know it. Set a depth stop or wrap tape around the bit at the bushing length + ~1 mm.
Dimensions
Overall | 96 × 40 mm, plate 3 mm, lip 20 mm high |
Hole pitch | 50 mm |
Edge to first hole | 35 mm (from inside face of the lip) |
Marking holes | Ø2.5 mm through |
Test-fit counterbores | Ø7.3 mm × 2 mm |
Door thickness | 15–19 mm |
Remix it
The design was made in Tinkercad, so it's easy to adapt: move the holes for a different edge distance or change the pitch for another handle. Always check the hole spacing of your own handle with a caliper first. Manufacturer specs aren't always exact.
Note on images
The renders show how the template is used. They are not photos.
Print settings
Setting | Value |
|---|---|
Printer | Creality K2 Pro Combo (any FDM printer works) |
Slicer | Creality Print (OrcaSlicer-based) |
Filament | Creality HyperPLA; any PLA or PETG works |
Nozzle | 0.4 mm |
Layer height | 0.16 mm |
Walls | 4 |
Top / bottom layers | 5 / 5 |
Infill | 40 % gyroid |
Outer wall speed | ~100 mm/s (for dimensional accuracy) |
X-Y hole compensation | +0.1 mm |
Elephant foot compensation | 0.15 mm |
Supports | None |
Brim | None |
Orientation | As supplied: plate flat on the bed, lip pointing up |
Print time | ~20–25 min |
Tip: if the Ø2.5 mm holes come out too tight for your awl, run a 2.5 mm drill bit through them by hand. That's quicker than reprinting.
Bill of materials / tools
Printed template (1×)
Awl or sharp pencil
7 mm brad-point wood drill bit
Depth stop or masking tape
StoreMax Handle Round