1 / 6
Modular 3×4 frame for P4 64×64 LED panels (256 mm) – Raspberry Pi inside. — zdjęcie 1
1 / 6

Modular 3×4 frame for P4 64×64 LED panels (256 mm) – Raspberry Pi inside.

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A support-free, dovetailed mounting frame for twelve 256 × 256 mm P4 HUB75 panels, with a hidden Raspberry Pi 4/5 and a

Ocena
0 / 5
Polubienia
0
Pobrania
3
Wydruki
0
Wyświetlenia
24
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Wall-mounted
Licencja
Creative Commons — Attribution

A full mounting frame for a 3 × 4 wall of common P4 64×64 RGB LED panels (256 × 256 mm, the "P4-2121-64X64-32S" type sold on AliExpress). The wall is 768.6 × 1024.9 mm and drives from a Raspberry Pi 4 or 5 with a HUB75 shield, all hidden inside the frame. A small pod on top holds a Pi Camera Module in portrait, tilted 15° down at whoever stands in front of the screen.

Everything prints on a Prusa CORE One (250 × 220 mm bed) with no supports.

Features

  • 20 printed nodes screw into the panels' brass corner inserts, and 31 rails join them with dovetails into one rigid lattice.

  • Rails also screw into the panels' mid-edge and bottom-centre inserts through slotted holes, giving 84 M3 screws in total.

  • The frame is 46 mm deep, with room inside for the Pi, shield and wiring.

  • 32 mm cable windows in every rail let a 16-pin HUB75 ribbon with its plug pass through.

  • Wall mounting by keyholes, with 6 keyholes on the back and about 8 mm of slide, or optional ear brackets.

  • The Pi platform has three fixing options: self-tapping screws, heat-set inserts, or a bolt and nut.

  • Countersunk seats for flat-head M3 screws, so the back sits flush.

  • Elephant-foot chamfers on every mating bottom edge, so first-layer squish doesn't bind the joints.

  • Every overhang is 45° or less, the only bridges are short (4–14 mm), and nothing needs supports.

  • Fully parametric OpenSCAD source is included: panel size, gap, depth, clearances and Pi stack height can all be changed.

Files – what to print

  • 00_fit_test_PRINT_FIRST – a junction node plus rail ends. Check the dovetail fit, the M3 holes and the keyhole before printing the rest.

  • 00b_DOVETAIL_GAUGE – three test sockets at 0.05, 0.10 and 0.15 mm clearance, marked with 1, 2 and 3 dots.

  • 01_nodes_junction_x6

  • 02_nodes_edge_x10_corner_x4

  • 03_rails_vertical_x7

  • 04_rails_vertical_x1_horizontal_x6

  • 05_rails_horizontal_x2_outer_x6

  • 06_rails_outer_x7_top_mount_x1

  • 07a / 07b / 07c – the Pi platform rail. Print only one: self-tapping, heat-set insert or bolt-and-nut version.

  • 08_camera_pod_body_and_lid

  • OPTIONAL_09_wall_ears_set – only needed if you use ear brackets instead of keyholes.

  • p4_frame_v3.scad – the source. Render with -D H=46 -D variant="B".

Print settings

  • PETG recommended, because the panels run warm.

  • 0.4 mm nozzle and 0.2 mm layers.

  • 5 perimeters, 40% gyroid infill, 5 top and 5 bottom layers.

  • No supports and no brim. Keep the slicer's elephant-foot compensation on.

  • Print everything as laid out, panel face down.

  • Expect roughly 2 kg of filament for the full set.

Hardware

  • 84 × M3 × 25 flat-head countersunk screws (DIN 7991 / ISO 10642), plus a long-shaft 2 mm hex key.

  • 2 × M3 × 12 to fix the pod to the frame, and 4 × M3 × 12 countersunk for the pod lid.

  • 4 × M2.5 × 6 for the Pi, plus M2.5 heat-set inserts or nuts if you print 07b or 07c.

  • 4 × M2 × 5 self-tapping screws for the camera.

  • A Pi 5 camera cable (22-pin to 15-pin), 500 mm. A Pi 4 needs a 15-pin cable instead.

  • 6 wall screws with heads of 8.2 mm or less, standing about 5 mm proud, with suitable anchors.

  • If you use ear brackets, the 12 bracket screws are M3 × 50.

Assembly

  1. Lay the panels face down on a soft mat, with the arrows on the back all pointing the same way.

  2. Place the nodes on the corner inserts.

  3. Drop the rails in from above. The dovetails slide down onto the node tenons.

  4. Screw everything down. Horizontal rails have an engraved arrow that must point up.

  5. Fit the Pi on its platform rail behind the top-middle panel.

  6. Screw the camera pod onto the top-centre rail and route the camera cable down through the slot.

  7. Hang the wall on six screws spaced on a 256.3 mm grid.

Notes

  • Measure your Pi plus shield from the top of the board to the highest plug. The default allows 32 mm.

  • Check the back of the top-middle panel for anything taller than the rim before fitting the Pi.

  • If the dovetails print loose or tight on your machine, print the gauge and set c in the SCAD to match.

Tags: LED matrix, HUB75, P4, 64x64, LED wall, Raspberry Pi 5, Raspberry Pi 4, Pi camera, frame, modular, dovetail, support-free, Prusa CORE One, OpenSCAD, parametric

Tagi