1 / 5
Hollow-Face Illusion Capybara - the face that follows you (4-colour AMS wall art) — zdjęcie 1
1 / 5

Hollow-Face Illusion Capybara - the face that follows you (4-colour AMS wall art)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Hollow capybara face that seems to pop out and follow you as you move. Wall frame, 4 colours, no supports.

Ocena
0 / 5
Polubienia
0
Pobrania
2
Wydruki
0
Wyświetlenia
13
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Home Decor
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

The animation (GIF) shows the camera moving side to side in front of the model: the capybara seems to turn its head and follow you, but the face is actually HOLLOW. This is the hollow-face illusion, the one that goes viral on video: your brain refuses to see a face pushed inwards, so it flips it into a normal bump, and then the motion parallax is read backwards. A calm capybara (long square head, wide blunt muzzle, small high eyes, little round ears) in a wall frame, 150 × 160 mm, four AMS colours, flat back, no supports.

How to get the effect

  • Light it from below and in front (a small shelf light or a phone torch held low). Lit from below, the hollow face shades exactly like a real face lit from above (see the comparison picture).

  • Look with one eye closed, or film it on a phone while walking past it. With both eyes up close, stereo vision breaks the effect; from 2 to 3 m it works with both eyes.

  • The colours help: the deepest part (the muzzle) is the lightest tan and the shallow rim the darkest brown, the opposite of what real shadows would do, so the paint itself says "this part is closest".

Details

  • Frame 150 × 160 × 37.5 mm; the face is sunk 28 mm into it, the deepest point is the wide blunt muzzle.

  • Short fur strokes (0.24 mm relief) running back from the muzzle, small eyes with heavy calm eyelids, ear hollows, nostril slits on top of the muzzle, split lip and a straight mouth.

  • Frame with outer chamfer, a band of seigaiha wave scales engraved 0.4 mm, a bead and a cove moulding. Small embossed HANMA mark.

  • Two keyhole slots in the back (4.6 mm screw shank, 10 mm head), 38 mm either side of centre, with 45° roofs so they print without bridges.

Printing

  • One piece, back flat on the bed, face opening upwards: the whole face is a height field seen from above, so there is no overhang anywhere and no supports.

  • Bambu Lab A1 mini + AMS lite, 0.4 mm nozzle, 0.20 mm layers, 15 % infill. The 3MF has the colours assigned.

  • Colours change mostly by layer height (light tan #C99A66 at the bottom, mid brown #A4703F, dark brown #7C4C2A, chocolate #3A2318 for the frame top, eyes and nostrils), so the sides show a neat ombré stripe.

  • Slicer estimate: 5 h 47 min, 210 g (light tan 90.8 g, mid brown 53.0 g, dark brown 45.4 g, chocolate 20.4 g), about 52 filament changes (the eyes and nostrils share layers with other colours).

How it was checked

  • Geometry: every face normal points to the viewer (minimum z component 0.043 > 0), the face sits below the rim everywhere and the deepest point (28 mm) is on the muzzle. Control: the convex version is rejected by the same test.

  • Illusion, simple simulation (Lambert shading with cast shadows): the hollow mask lit from below correlates r = 0.89 with the convex face lit from above. Control: the hollow mask lit from above gives r = -0.28 (it reads as hollow).

  • Illusion, Cycles path-traced renders (perspective, bounced light): r = 0.68 for hollow-from-below vs convex-from-above; control r = -0.26.

  • Printability: 0.00 mm² of overhang steeper than 46° off the bed. Control: the same part upside down would have 20,108 mm². One single body, fits 175 × 175, 12.6 mm of plastic above each keyhole.

  • Colours: no colour overlaps another (worst 0.003 mm³); control: shifting one colour 0.6 mm creates 12,817 mm³ of overlap.

About this design

Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.

Español

Ilusión de la cara hueca: una capibara simpática hundida en un marco de pared que, iluminada desde abajo y vista con un ojo o en vídeo, parece salir hacia ti y te sigue con la mirada. 4 colores AMS, sin soportes, 5 h 47 min y 210 g.

العربية

خدعة الوجه المجوف: وجه كابيبارا لطيف محفور داخل إطار للحائط، عند إضاءته من الأسفل والنظر إليه بعين واحدة أو في فيديو يبدو بارزا ويتابعك بنظره. أربعة ألوان AMS، بدون دعامات، ٥ ساعات و٤٧ دقيقة و٢١٠ غرامات.

Tagi