NightOwl LEDs for Lane Indication
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Added lane indicator LEDs using BarfTurtle sticks
- Ocena
- 0 / 5
- Polubienia
- 7
- Pobrania
- 8
- Wydruki
- 1
- Wyświetlenia
- 99
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Voron Parts & Upgrades
- Licencja
- GNU General Public License v3.0
Add some bling to your NightOwl with the BarfTurtle LED sticks (example link: https://west3d.com/products/box-turtle-led-kit). Use these for lane indication
This replaces the front skirt of the NightOwl. The diffuser is a multibody object intended to be printed as one piece with multiple colors (you have a filament changer after all!). A single pice stl is also included if you want to print in a single translucent/white filament).
Use 2x M3x8 screws (no longer!) to attach the LED holder to the front skirt. You're screwing into plastic, so only tighten to just snug. Be careful.
The LEDs are BRIGHT! They easily shine through my primary color (Ambrosia Galactic Grey). Adjust the brightness via config below.
Config changes (assuming you're using AFC, you're on your own for HH):
Add this to your AFC_NightOwl_1.cfg:
[AFC_led AFC_Indicator_Bar]
pin: NightOwl:RGB
chain_count: 16
color_order: GRB[AFC_stepper lane1]
led_index: AFC_Indicator_Bar:9-16
[AFC_stepper lane2]
led_index: AFC_Indicator_Bar:1-8
Add this to your AFC.cfg:
#--=================================================================================-
#------- LED Settings ---------------------------------------------------------------
#--=================================================================================-
led_name: AFC_Indicator # LED name from the [AFC_led] section in AFC_Hardware.cfg.
led_fault: 0.75,0,0,0 # Fault color (R,G,B,W) 0 = off, 1 = full brightness.
led_ready: 0,0.5,0,0 # Ready color (R,G,B,W) 0 = off, 1 = full brightness.
led_not_ready: 0.75,0,0,0 # Not ready color (R,G,B,W) 0 = off, 1 = full brightness.
led_loading: 0.75,0.75,0.75,0 # Loading color (R,G,B,W) 0 = off, 1 = full brightness.
led_tool_loaded: 0,0,0.75,0 # Loaded color (R,G,B,W) 0 = off, 1 = full brightness.
led_buffer_advancing: 0,0,0.75,0 # Buffer advancing color (R,G,B,W) 0 = off, 1 = full brightness.
led_buffer_trailing: 0,0.75,0,0 # Buffer trailing color (R,G,B,W) 0 = off, 1 = full brightness.
led_buffer_disable: 0,0,0,0.5 # Buffer disable color (R,G,B,W) 0 = off, 1 = full brightness.Check out my other NightOwl mods:
BoxTurtle v1.1 Hub/Buffer combo: https://www.printables.com/model/1864558-boxturtle-v11-hub-for-nightowl
Filamentalist FV3 Respoolers: https://www.printables.com/model/1577021-nightowl-filamentalist-fv3-mod
Apex extruders (dual sensors): https://www.printables.com/model/1865211-dual-sensor-apex-extruders-for-nightowl
Smol v2 (HGX 2.0) extruders (dual sensors): https://www.printables.com/model/1865219-dual-sensor-smol-v2-hgx20-extruders-for-nightowl