Honeycomb Soda Can Holder for Traeger P.A.L. Rail
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Keep your drink within reach while grilling with this two-piece holder for a standard 12 oz soda can.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 1
- Wydruki
- 0
- Wyświetlenia
- 15
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Kitchen
- Licencja
- Creative Commons — Attribution — Share Alike
Honeycomb Soda Can Holder for Traeger P.A.L. Rail
Keep your drink within reach while grilling with this two-piece holder for a standard 12 oz soda can.
I wanted an open design with thinner walls to use less material, while keeping a solid mounting area. The honeycomb cup has a tall back and a low, sloping front rim so the can is easy to grab. Bottom crossbars support the can and let condensation drain.
I printed this in ASA-CF and confirmed that both the can and rail mount fit perfectly on my setup.
Fit and Features
- Fits a standard 12 oz / 355 mL can, approximately 66 mm in diameter.
- 68 mm inside diameter with 2 mm retaining walls.
- Sloping rim: 83.6 mm high at the back and 42 mm at the front.
- Reinforced rear mounting section and a separate rail clip.
- Recessed hardware keeps screw heads below the rail-facing surface and screw tips clear of the can.
- Honeycomb removes approximately 16% of modeled volume compared with the same thin-walled holder without the openings. Actual filament savings depend on slicing.
The rail used for this design measured 62.25 mm high × 9.25 mm thick. Check your can and rail dimensions before printing; slim cans and other rail profiles may fit differently.
Printing
Print one of each part in ASA-CF:
- soda_can_holder.stl: upright, with the bottom crossbars on the bed.
- clip.stl: on its side, as already oriented in the supplied file.
Use settings appropriate for your printer and filament, and inspect the sliced layers before printing.
Hardware and Assembly
You will need:
- 2 × M4×12 socket-cap screws.
- 2 × M4 hex nuts.
- A matching Allen key.
The screw-head recesses are 8 mm diameter × 4.4 mm deep, sized to recess the tested 4 mm-tall heads. Check your head diameter. M4×8 screws are too short, and flat-head screws are not intended for these recesses.
1. Insert the nuts into the pockets inside the holder.
2. Place the clip against the flat back and align both holes.
3. Insert the screws from the outside, rail-facing side. Tighten snugly with the assembly off the grill.
4. Check that the hardware remains recessed, then gently fit the holder onto a cool rail. Test with an empty can before trying a full one.
Keep the holder away from the hot barrel and flame. Check the mounting location against your filament’s temperature limits. Long-term heat and load performance have not been validated.
Credits
The honeycomb and sloping-rim appearance was inspired by Sergej’s can holder (https://www.printables.com/model/750383-can-holder-skadis-pegboard-wallmount), published under CC BY-NC-SA 4.0. This holder was independently modeled; no reference mesh was copied.
The rail clip follows the mounting-design lineage of ThomaS’s P.A.L. accessories (https://makerworld.com/en/models/130799), via Dan’s Thermapen holder remix (https://makerworld.com/en/models/594815-traeger-p-a-l-thermapen-holder), with a redesigned separate clip and recessed fastening arrangement.
An independently made accessory, not an official or affiliated Traeger product.
