Battery Pack for 38120 Cells
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
This print is a durable case holding four 38120 LiPo cells and a Daly 4S12V40A BMS with two Anderson PP connectors.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 3
- Wydruki
- 0
- Wyświetlenia
- 57
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
I was looking for a hard-case for field batteries for amateur radio operations. After finding no suitable designs, I made my own. These prints, when assembled with all extra components, will create a 12 volt DC battery pack, suitable for powering 12 volt radios for field operations. This is currently in service powering a Yaesu FT-891 HF radio.
Step 1 - Print the case halves
The original design was printed in ABS, but other materials like ASA should be suitable.
Step 2 - Gather your materials
You will need:
Tape, Kapton
Soldering Iron
Heat Gun
Crimp tools for Ring Terminals and Anderson Power Pole contacts
Drill, with #19 drill bit
Screwdriver, Phillips #2
Hammer and Punch w/ Hard Surface or Parallel Jaw Pliers
1x - Case, Battery, Top
1x - Case, Battery, Bottom
1x - BMS, Daly 4S12V40A
2x - Connector, Lever-style, Wago 221
2x - Connector, Body, Anderson Power Pole (red+black)
2x - Contact, Anderson Power Pole, 261G2-LPBK
2x - Wire, 10 Ga, Stranded, Red Color, 5 inch length
2x - Wire, 10 Ga, Stranded, Black Color, 5 inch length
1x - Wire, 10 Ga, Stranded, Red Color, 6 inch length
2x - Terminal, Crimp, Ring, 10-12 Ga, Heat Shrink, McMaster-Carr 7036K78
5x - Terminal, Crimp, Ring, 24-26 Ga, Heat Shrink, McMaster-Carr 7036K94
4x - Battery, 38120, "Headway" Style, 3.2 VDC, 10K mAh Capacity, (Blue exterior)
3x - Bus Bar, "Headway" style, 2-position, 1-5/8 inch hole spacing
8x - Screw, Button-Head, Hex Drive, M6 x 1.0 - 8 mm (Order with batteries and bus bars)
1x - Clamp, Mounting, Anderson Power Pole 1462G1
2x - Nut, Press-in, #4-40, PEM-Style, McMaster-Carr 95185A120
2x - Screw, Pan Head, #4-40 x 1/2 inch length, McMaster-Carr 90272A110
4x - Screw, Pan Head, #10-24 x 2-1/4 inch length, McMaster-Carr 90272A367
4x - Insert, Threaded, Heat-Set, #10-24 x 0.225, McMaster-Carr 93365A150
Step 3 - Prepare 10 gauge wire
Cut two 5 inch lengths of 10 Gauge red wire and two 5 inch lengths of 10 gauge black wire.
On one end of each of the 4 wires, strip insulation and crimp an Anderson Power Pole contact on the end.
Assemble a black and a red wire in each Anderson Power Pole connector body.
On the other ends of the four 10 gauge wires, strip sufficient material to install in the Wago 221 lever-lock connector.
Install the red wires into the left and right positions on one of the Wago 221 lever-lock connectors.
Install the black wires into the left and right positions on the other Wago 221 lever-lock connector.
Cut one 6-inch length of 10 gauge wire with red insulation. Strip one end for a ring terminal and crimp on a ring terminal and recover the heat shrink around the wire.
On the other end of the 6-inch length of 10 gauge red wire, strip sufficient insulation to install into the Wago 220 lever lock connector, and install the red wire in the center position of the Wago 221 containing the red wires.
On the Daly BMS, strip sufficient insulation from the black wire for installation into the Wago 221 with the black wires. Install the black wire from the Daly BMS into the Wago 221 containing the black wires.
On the Daly BMS, strip sufficient insulation from the blue wire for installation into a ring terminal. Install a 10 gauge ring terminal, crimp, and recover the heat shrink boot.
Step 4 - Prepare the 24 gauge wire
On the Daly BMS, there is a 1x5 pin connector for monitoring each cell's voltage. Strip sufficient insulation to install the 24 gauge ring terminals, and then crimp five ring terminals on the end of each wire terminating at this connector.
Step 5 - Prepare the Power Pole Clamp
In the mounting hole of each half of the Anderson Power Pole Clamp, drill the hole out with a #19 drill bit.
Set a PEM nut in the hole and crimp into position with a hammer and punch or parallel jaw pliers.
Step 6 - Prepare the case halves
Test fit the Daly BMS in the top half. You may need to trim material to fit the wires.
Install the brass heat set inserts in the top half of the case.
Step 7 - Install the BMS and Power Poles
Locate the temperature probe from the BMS and plug in to the side connector.
Locate the sense wire assembly and plug it in to the bottom of the BMS
Press the BMS into the position on the top half of the case.
Install the Anderson power poles in position in the top half of the case, set the Power Pole Clamp in position, and install the #4-40 screws to hold them in position, using care to not overtorque the screws and damage the case half.
Step 8 - Assemble the batteries
Set the batteries in position so they are in series, making sure the blue wire is in position to be connected with the negative terminal of the last battery.
Connect the blue wire and battery sense ground wire to the negative terminal of the last battery.
Install bus bars to ensure the batteries are in series, and locate the appropriate sense wire ring terminal in position when installing bus bars.
Install the red wire to the positive end of the string of batteries.
Step 9 - Finalize wire routing
Route power wires to avoid being pinched or shorted
Route sense wires to avoid being pinched or shorted.
Place the temperature probe on one of the batteries and secure into place with kapton tape.
Use Kapton tape to help insulate any connections that may require extra insulation.
Step 10 - Assemble the case
With the battery case top half on the bench and holding all batteries and wires, carefully set the case bottom half onto the case top half.
Check around the perimeter of the case, to make sure all mounting surfaces are flush
Squeeze the case halves together, and flip the unit onto the bottom half.
Install the four #10-24 mounting screws and tighten by hand.
Step 11 - Charge the Batteries
Hook your new battery pack up to an approved charger for Lithium Polymer batteries, and give it a charge!