QRP Labs QMX / QCX-mini Kneeboard with Magnetic Paddle Pad
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Compact kneeboard for the QRP Labs QMX and QCX-mini with a magnetic paddle pad and shock-cord radio retention.
- Ocena
- 5 / 5
- Polubienia
- 9
- Pobrania
- 28
- Wydruki
- 1
- Wyświetlenia
- 403
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Electronics
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Overview
This is a kneeboard for the QRP Labs QMX that also fits the QCX-mini, which uses the same 95 x 63 x 25 mm case. The radio sits display-up in a shallow pocket and is held down by a single shock cord that stays attached to the board. A 2 in steel fender washer, set flush in the paddle tab, gives any paddle with a magnetic base a solid place to sit. One 1.5 in elastic strap holds the board to your leg.
On the Air
It's built for POTA, SOTA and other field operating, where there's no table and you're sending CW from a camp chair, a log or a car seat. Both ends of the radio stay open, so the BNC, power, USB, key and audio jacks are all reachable with the radio strapped in
Print Settings
Recommended settings. These haven't been verified on a final print yet.
Printer: Bambu Lab, 0.4 mm nozzle
Material: PETG (PETG-CF if you want it stiffer). PETG handles sun and a hot car better than PLA. Of course you could also use PCTG, ASA, ABS, etc.
Layer height: 0.2 mm
Walls: 4 loops, 5 top and 5 bottom layers
Infill: 40% or more gyroid
Supports: none
Orientation: flat, label side down. The underside channel and knot seats print as short bridges and 45-degree or steeper slopes.
Hardware and Assembly
1x 2 in fender washer, 50.8 mm OD x 1.3 mm thick - https://a.co/d/0co72TII - You can get these individually at hardware stores.
1x 3 mm shock cord, about 450 mm long - https://a.co/d/0aANtvTP
1x 1.5 in (38 mm) strap with buckle or hook-and-loop closure - https://a.co/d/0cXGkovK
E6000 or CA glue for the washer - https://a.co/d/0ih6trp7 - Or get the "Gel" super glue from Harbor Freight
Glue the washer into its pocket. The pocket is 51.2 mm across and 1.4 mm deep, so the washer sits flush. The "rounded" edge of the washer should face up (you can feel the difference)
Tie a stopper knot in one end of the cord. Thread it up through the left rear keyhole from underneath, so the knot sits in the knot seat under the board.
Run the cord forward and down through the left front hole. Then run it along the channel on the underside and up through the right front hole.
Set the radio in the pocket. Run the cord over the radio and press it into the right rear keyhole through its slit.
Pull the cord to the tension you want and tie a stopper knot under the right rear keyhole. Trim the tails.
To remove the radio, squeeze the cord out of the rear slits. The knots stay tied, so the tension setting is kept for next time.
Thread the strap through the two slots on the tab and around your leg.
Makes, remixes and fit reports on other radios are welcome.
73!