1 / 5
Print-in-Place Vernier Caliper (two-color, mm + inch) — zdjęcie 1
1 / 5

Print-in-Place Vernier Caliper (two-color, mm + inch)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Working print-in-place vernier caliper: 0.1 mm and 1/128" verniers, two-color markings, built-in supports.

Ocena
0 / 5
Polubienia
4
Pobrania
24
Wydruki
0
Wyświetlenia
81
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

A fully functional vernier caliper that prints in place: the slider comes off the plate already captured on the beam. Snap off the built-in supports, push the slider free and start measuring.

Features

  • Print-in-place: the slider rides on diamond-profile rails with 0.2 mm clearance and can't fall off (an end stop on the back holds it at full opening).

  • Metric scale on the front (0–150 mm) with a 0.1 mm vernier.

  • Imperial scale on the back (0–6", 1/16" divisions) with a 1/128" vernier.

  • Outside jaws, thin inside jaws for bores (down to ~2.5 mm), knurled thumb wheel.

  • Two-color scale marks: every tick and digit is a shallow recess with a colored plug under it. They stay readable at an angle, and the first layer stays one color, so no first-layer strings in the scale. Use any color you like for the scale marks.

  • No slicer supports needed. The supports are part of the model: a small block under the upper inside jaw (with a grab tab) and thin strips under the rails. They print 1 layer away and snap off.

Files

The 3MFs contain the model only (no printer or profile settings), so they open on any printer. Each is already split into parts: beam, slider and supports on filament 1 (body color), scale marks on filament 2, body color first on each layer. Pick your printer and filaments, then apply the settings below.

  • caliper_BambuStudio.3mf: for Bambu Studio.

  • caliper_SnapmakerOrca.3mf: for Snapmaker Orca.

  • caliper_OrcaSlicer.3mf: for OrcaSlicer.

Bambu Studio and OrcaSlicer say they're loading geometry data only ("invalid config" in Bambu Studio). Click OK: it just means the file brings no printer settings. The parts and filament slots load correctly, and your own printer profile is used.

  • caliper.stl: for any slicer. Prints in one color as is (the scale shows as shallow engraved marks), or in two colors:

    1. Load caliper.stl and set the whole model to your scale mark color.

    2. Right-click → Split → To parts.

    3. In the object list, select the beam and slider (the two largest parts) and set them to your body color.

    The breakaway support pieces can be either color, since they snap off.

Print settings (0.4 mm nozzle, PLA)

Start from your printer's 0.20 mm Standard profile and change these:

Setting

Value

Why

Layer height / first layer height

0.2 / 0.2 mm

The gaps and scale marks are designed on 0.2 mm layers

Elephant foot compensation

0

Anything higher shrinks the thin first-layer marks until they drop out

Brim

None

A brim fuses to the slider and the support strips

Supports

Off

Supports are built into the model

Wall loops

4

Top / bottom shell layers

5 / 4

Sparse infill

20 %

Wall generator

Arachne

Cleaner thin ticks and digits

First layer speed

20 mm/s

The scale is on the first layers

Outer wall speed

100 mm/s

Every mark edge is an outer wall

Top surface speed

60 mm/s

Cleaner inch scale on the top face

Avoid crossing walls

On

Fewer strings across the scale marks

Where to find them

  • Bambu Studio: Process → Quality (layer heights, elephant foot, Arachne, avoid crossing walls), Strength (walls, shells, infill), Speed, Support, Others (brim). Plate settings → check the body color prints first.

  • OrcaSlicer / Snapmaker Orca: the same names, in the Quality, Strength, Speed, Support and Others tabs. Plate settings → first layer and other layers sequence: body color first.

  • Multi-nozzle printers (Snapmaker U1 and other tool changers): turn on ooze prevention and lower the idle temperature of the scale-mark nozzle (about 40 °C below printing), so it doesn't drip while the body prints.

  • Single-nozzle printers with an AMS or MMU: the default purge/flush amounts are fine; raise them slightly if black shows up in the white.

For crisp, smudge-free scale marks

The scale is hundreds of tiny marks, so every start, stop and travel counts. These three together took my inch side from gray wisps to perfectly clean:

  • Dry both filaments before printing (PLA: about 50 °C for 6–8 hours). Damp filament strings badly and leaves gray wisps around the marks.

  • Print the scale-mark filament about 10 °C cooler than usual, with faster retraction (around 45 mm/s). It oozes less between the many small marks.

  • Run a flow / pressure-advance calibration for both filaments (or turn on the printer's dynamic flow calibration). Tuned pressure advance gives clean starts and stops on each tiny mark.

Other tips

  • Smooth plate recommended for a clean metric face.

  • A 0.2 mm nozzle gives the finest scale marks: use 0.1 mm layers, 5 walls, 40 % infill.

After printing

  1. Pull the tab past the tip of the upper inside jaw to peel the block off (pliers help), then peel off the strips under the rails.

  2. Free the slider with a firm push along the beam. It loosens up after a few strokes.

  3. Close the jaws and check both verniers read 0.

Accuracy

It's a printed tool: expect roughly ±0.1–0.2 mm, depending on your printer and filament. Great for everyday measuring, 3D-printing work and learning to read a vernier; not a replacement for a steel caliper where precision matters.

Tagi