1 / 4
Fennec SMG Collector Desk Ornament with Cradle : COD — zdjęcie 1
1 / 4

Fennec SMG Collector Desk Ornament with Cradle : COD

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Inert Fennec SMG display model from CoD Mobile: Vector-style profile, no-support parts, snap cradle, embossed nameplate.

Ocena
0 / 5
Polubienia
1
Pobrania
2
Wydruki
0
Wyświetlenia
26
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Props
Licencja
Creative Commons — Attribution

A non-firing, glue-together desk sculpture of the Fennec from Call of Duty: Mobile, designed for FDM printing with no supports. Assembled on its stand it measures 244 x 70 x 140 mm. The largest part is 180 mm long and the tallest print is 50 mm, so everything fits a 180 x 180 x 180 mm printer. Unofficial fan art; Call of Duty and the weapon names belong to Activision. Decorative display model only.

Lore:
The Fennec joined Call of Duty: Mobile as the new base SMG in Season 11, the game’s first-anniversary update, along with an Akimbo gun perk that made it notorious. It is the KRISS Vector under the name the series adopted with Modern Warfare (2019): a very high fire rate, low recoil close-quarters weapon.

Reference geometry:
The Vector’s look comes from its Super V layout, where the action is redirected down behind the magazine well, so the lower housing is deep and angular while the bore sits low. The ornament keeps the recognisable cues: a long flat upper with a full-length rail, a diagonal sweep from the rear of the upper down to the grip, a grip set mid-body, a magazine well flared 2 mm proud on each side, a blunt front face with a lamp bezel above a low barrel, and a triangular skeleton stock. At 244 mm it is roughly 40% of a real Vector with the stock out. It is a stylised interpretation, not a trace of the in-game mesh.

How it is split:

  • Receiver, left and right halves (136 mm): upper, Super V lower housing, flared magazine well, trigger guard and full-length rail, split on the centre plane. Both halves print flat on the split face.

  • Stock: one flat 10 mm piece with a 12 x 12 mm tongue that keys into the back of the receiver.

  • Grip and magazine: separate, printed upright, each with a 12 x 6 mm tenon.

  • Optic: prints standing on its front face and slides onto the dovetail rail.

  • Barrel: solid, printed muzzle-down, with a D-spigot.

  • Muzzle cap: solid orange plug.

  • Display cradle: plinth, a front upright under the chin, a rear upright under the grip, slide-in nameplate.

Joints and tolerances (clearance is per side):

  • Alignment pins: 4.00 mm x 9.6 mm pins in 4.40 mm x 5.0 mm deep holes, 0.20 mm.

  • Keyed tenons (grip, magazine): 6.0 mm thick tenons in sockets, 0.20 mm.

  • Stock tongue: 12 x 12 mm, 10 mm thick, in a rear socket, 0.20 mm.

  • Barrel seat: 8.0 mm D-spigot in 8.4 mm blind D-socket, 0.20 mm.

  • Muzzle cap: 6.0 mm x 4.0 mm D-spigot in 6.4 mm x 4.2 mm blind socket, 0.20 mm.

  • Optic on rail: sliding dovetail, 9.0 mm crown, 6.0 mm neck, 4.2 mm tall, 2.0 mm slots on 4.0 mm pitch, 0.25 mm.

  • Nameplate: 80 x 24 x 2.4 mm plate with 45 degree bevelled ends in a dovetail groove, 0.25 mm.

  • Cradle to plinth: two barbed legs (7.0 mm thick, 0.6 mm barbs) in a 7.4 x 10.4 mm mortise, 0.20 mm.

  • Weapon to cradle: 0.6 mm beads on two 2.2 mm spring arms click into 0.7 mm detent pockets.
    If your printer runs tight, do not scale: sand the pins or open the holes with a 4.5 mm drill.

Filament and colours:

  • Receiver halves, pins: Matte Charcoal PLA

  • Stock, grip, magazine, optic: Matte Black PLA

  • Barrel: Gunmetal Silk PLA

  • Muzzle cap, nameplate: High-Visibility Orange PLA (swap to white at 2.4 mm on the nameplate for contrast lettering)

  • Plinth, cradles: Matte Black PLA

Print settings:

  • Nozzle 0.4 mm

  • Layer height 0.12 mm for nameplate, optic, barrel and magazine; 0.16 mm for everything else

  • First layer 0.20 mm, elephant-foot compensation 0.15 mm

  • 4 walls, Arachne wall generator

  • 6 top and 5 bottom layers, monotonic top surface

  • Infill: 15% gyroid for body halves, 12% gyroid for plinth, 25% gyroid for cradles

  • Supports: none. Longest bridge is 12.4 mm; bridge fan at 100%

  • 5 mm brim on the barrel, grip and magazine

  • Nameplate colour change: pause at Z = 2.4 mm

  • Every STL is already in its print orientation and sits on Z = 0

Assembly:

  1. Dry-fit everything first.

  2. Glue six pins into the left receiver half, add glue to the split face, close the right half onto it, clamp.

  3. Glue the stock tongue into the rear socket, then the grip and magazine tenons from below.

  4. Glue the barrel spigot into the front face, flat side down, then glue the orange cap into the muzzle. The cap is permanent by design.

  5. Slide the optic onto the rail and tack it in place.

  6. Press both cradles into the plinth until the barbs click, slide the nameplate in from the front. Seat the grip base in the rear cradle and the chin in the front cradle.

Tagi