Jax Cosplay Head
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Cosplay head of Jax from The Amazing Digital Circus, based on the Blender model by Lucasz
- Ocena
- 0 / 5
- Polubienia
- 14
- Pobrania
- 16
- Wydruki
- 0
- Wyświetlenia
- 290
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Masks
- Licencja
- Creative Commons — Attribution
This is my cosplay head of Jax from The Amazing Digital Circus. My version goes by Greznedge these days but you can make one of her old look too.
Original model credit to Lucasz, available on Ko-fi:
https://ko-fi.com/s/f55a4f822b
This is a difficult and time-consuming print. I spent a lot of time wrangling Colorfabb LW-PLA so that the parts would be strong enough to use, and I am happy with the result but I do feel there could be improvements if I had to do it again. Additionally, be warned that the final head can be up to 2 kilograms and is therefore uncomfortable to wear for periods of more than a few hours. It can probably be lightened somewhat by changing slicer settings (fewer walls, less infill, etc) or using LW-ASA, but I have not tested those options myself. Something else to try is reducing the use of Varioshore TPU in the ears by cutting the lower portion about 1/3 of the way up from the head. That would retain the ability to bend, so as to avoid snapping them off on a harsh impact, but make them significantly lighter. With that said, here's how I did it.
NON-PRINTED MATERIALS
Krylon ColorMaster spray paint, Black, Gum Drop (Purple),Bright Idea (Yellow)
Krylon ColorMaxx spray paint, Smoke Gray
DupliColor 2 in 1 Hi-Build Filler & Sandable Primer
TotalBoat TotalBond Medium CA Glue and CA Activator Spray (head pieces and ears)
E6000 Craft Adhesive (eyeliner, face mesh, and hard hat mount)
PVC fursuit eye mesh from Benecreat
3M SecureFit Hard Hat Suspension OR Jackson Safety Advantage Hard Hat Suspension
FILAMENTS
Colorfabb LW-PLA Natural, ~1 KG. There are more and more foaming PLAs out there, most of them should work
Colorfabb Varioshore TPU Natural, ~400g
Prusament rPLA Wine Pigment, ~80g. Used for eyeliner as I liked the color
Generic PLA, ~1.5 KG for mesh form, connector pins, and suspension
TOOLS
Deburring tool
Handheld electric sander and 200 grit wet sandpaper
Tack cloth
Small binder clips (0.75 in)
Heatgun
Needle filing set
Masking tape of assorted widths (2 in, 1/8 in)
Shaving razor
Latex gloves
PROCEDURE
Print the head segments in LW-PLA. I have found that, on my CORE One, the default .15mm Structural preset with tweaked temperature and extrusion multiplier works better than any Colorfabb-provided profiles. Make sure that there aren't any soft spots near the top of the print, around where the overhang becomes severe. These appear as gaps in the surface, like underextrusion, and are weak structurally and difficult to paint over.
Print the lower segment of the ears in Varioshore TPU. This will allow the ears to move and bend slightly rather than breaking off in the event of an impact. They are very tall, so impacts are likely to happen.
Print the eyeliner in PLA. These are very spindly parts, and rather difficult to print. I have done my best to orient them and set up support settings, but you may need to change options as needed. Luckily it's also a small part and prints quickly.
Print the suspension adapter, connecting pins, and mesh forms in generic PLA. The mesh forms make use of PrusaSlicer's negative modifier function and are therefore only available in 3MF format, sorry about that
Assemble the head pieces. Leave the ear pieces disassembled for now, as they are easier to paint separately. Do a dry fit first and and join them together with superglue and activator once you can get them to sit flush. A deburring tool can help remove strings from the peg holes.
Sand the seams with 200 grit, as well as any other rough spots on the exterior. The needle files are handy for getting at some of the tighter corners here. Splashing a bit of water on the surface can help remove superglue more quickly.
Mask off the mount points for the ears and the edges of the eyes where the eyeliner will go later. The paint will prevent proper glue adhesion. Do the same with the ear pieces
Use a shaving razor to clean up strings and seams on the VarioShore parts. Be careful not to cut too deep, and keep the blades from clogging by removing cut bits with fine tweezers if needed.
Assemble the forms and tack them together with a small amount of superglue and activator to avoid squeezeout. Take notice of the direction you will insert the upper form, and draw an arrow so you don't put it in backwards. It only works if you put it in the right way around and it's impossible to tell what that is once the mesh is attached. Cut a piece of the PVC mesh roughly to the shape of the lower form and clamp it flat and taut. Heat it up with a heatgun, trying to heat as evenly as possible, and then very quickly press the positive form into it. This is helped by having one person hold the form and another use the heatgun. Once it has cooled, trim the flat parts off the edges.
Paint the LW-PLA pieces with filler primer. I found it helpful to place a trash bag over a camera tripod and place the head on top to more easily reach all sides.
DO NOT use primer on the VarioShore parts, as this will cause the paint to flake off when it flexes.
Paint the VarioShore parts with Smoke Gray ColorMaxx paint. This is purely to make the base color more similar to that of the filler primer, and may not be strictly needed with multiple thin purple coats.
Paint the face mesh black. Keep the can fairly far back and coat lightly to avoid filling in the holes.
After 24 hours to allow paint to cure, place the mesh back on the positive form and use masking tape to create the mouth lines and pupils. Try to get the edges as flat as possible. Take it back off the form and paint it yellow, again being careful to not fill in the holes.
Sand the main head and eartips with 200 grit, splashing water on the surface to keep the sandpaper from clogging. Try to get the seams as flat as possible. Clean it up with tack cloth and allow to dry, then paint with filler primer again.
Paint the lower ear segments purple. Don't get too close, or the solvent will build up and crackle or appear whiter than it should.
Wait another 24 hours for the paint to cure. Remove the masking tape from the face mesh and set it aside, that part is finished. Evaluate the Varioshore parts and if they're evenly purple, set them aside as well. If not, touch up with another coat.
Again wet-sand the main head and the eartips and clean up with tack cloth. If you feel it's sufficiently smooth to the touch, wait for it to fully dry from the sanding and then paint purple.
Once all LW-PLA parts are purple and cured for 24 hours, you can begin final assembly. Use as little superglue as you can while getting right up to the edge when assembling the ears, as both a gap and excessive squeezout at the seam will be fairly visible. If needed, sand with a flat needle file and touch up with another coat of paint.
Apply E6000 to the edges of the eyeliner parts and press them into the eye sockets. Hold them there one by one until they stay where they are.
Apply E6000 to the inside of the center section and the chin bar, insert the eye mesh through the neck hole, and hold it in place until it stays on its own. Allow 24 hours for glue to cure.
Lastly, assemble the hard hat suspension and place it into the head without gluing it, and put the head on to get a sense of where the suspension mount will need to go. The front is the side with two round cutouts for the eyes. I found poster hanging putty helpful to tack in place for this, but it's not strictly needed. Once you know where it's going, apply E6000 to the top of the suspension adapter and hold it in place until it stays where it is. Be fairly generous when applying the glue as the surface may not be completely flat.
Allow 24 hours for the glue to cure, and you're done!
This was a very fun project to work on and I am very happy with the result.