1 / 6
XL Timing Pulley 30T & 45T, 8 mm Bore, M5 Set Screws – Printed & Tested — zdjęcie 1
1 / 6

XL Timing Pulley 30T & 45T, 8 mm Bore, M5 Set Screws – Printed & Tested

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

XL pulleys, 30 and 45 teeth, 8 mm bores, M5 set screws threaded into the plastic. Printed and run on a 150XL belt.

Ocena
0 / 5
Polubienia
0
Pobrania
7
Wydruki
0
Wyświetlenia
20
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

An XL timing pulley pair, 30 and 45 teeth on 8 mm bores, printed and run on a 150XL belt. Two M5 set screws per hub thread straight into hex-shaped holes in the plastic, with no nut or insert; the 45-tooth pulley has five spokes, and both print their flanges in place.

Printing

  • Printed on an Anycubic Kobra 2 Max in PETG, 0.15 mm layer height.

  • Print the "-w-supports" STLs. Breakaway supports hold each top flange, which prints in place; snap them off after printing.

  • Turn the M5 set screws straight into the hex holes: they cut their own thread in the plastic.

  • The STLs are exactly what was printed for the photos: pulley 1 with 0.2 mm of print compensation, pulley 2 with none. The STEP file is nominal size.

Files

  • STEP at true size: one file with every part of the drive, the belt included.

  • STL for printing:

    • Imperial-XL-30T.stl - pulley 1, 30 teeth, without supports

    • Imperial-XL-45T-P2.stl - pulley 2, 45 teeth, without supports

    • Imperial-XL-30T-w-supports.stl - pulley 1 with breakaway supports under its top flange: print this one

    • Imperial-XL-45T-P2-w-supports.stl - pulley 2 with breakaway supports under its top flange: print this one

Need another size?

These were designed in the CheapCADTools Timing Pulley Generator. Open this exact design there and change the teeth, bore, hub, set screws, spokes or flanges, or switch to any of 34 belt profiles (GT2, HTD, T5, AT5, XL, MXL and more): https://cheapcadtools.com/samples/xl-30t-45t-printed-m5-threaded-set-screws/?ref=printables

Belt length for your centre distance, free: https://cheapcadtools.com/belt-length-calculator/?profile=Imperial%7CXL&z1=30&z2=45&n=75&ref=printables

Paid, so you know: designing in the generator is free; downloading a new STL, STEP, DXF or SVG from it costs tokens (an STL is 3 tokens, about 15 cents). The files on this page are free.

All settings, as designed

Drive

  • Family: Imperial; Pitch: XL

  • Belt Height (mm): 12.5; Clearance Height (mm): 2

  • Centre Distance (mm): 94.47 (belt 75 teeth)

Pulley 1

  • Num. Teeth: 30; Bore Diameter (mm): 8

  • 3D Print Compensation (mm): 0.2; Tooth Clearance: Standard; Backlash: Standard

  • Hub OD (mm): 25; Hub Height (mm): 15

  • Retention Method: Set Screw (threaded); Set Screw Size: M5; Number of Screws: 2; threaded hole: Hex, Hex Flats: 82% of the screw's diameter

  • Flanges, 3D Print: Flange Height (mm) 3; Flange Angle (°) 15; Rim Radius (mm) 4; Top flange as separate part: no

  • Add Print Supports: Nozzle Dia. (mm) 0.4; Max Spacing (mm) 5; Air Gap (mm) 0.2

Pulley 2

  • Num. Teeth: 45; Bore Diameter (mm): 8

  • 3D Print Compensation (mm): 0; Tooth Clearance: Standard; Backlash: Standard

  • Hub OD (mm): 25; Hub Height (mm): 15

  • Retention Method: Set Screw (threaded); Set Screw Size: M5; Number of Screws: 2; threaded hole: Hex, Hex Flats: 82% of the screw's diameter

  • Spokes: Spoke Count 5; Spoke Width (mm) 8; Hub OD (mm) 25; Rim Depth (mm) 6; Fillet Tip (mm) 3; Fillet Base (mm) 3; Spoke Height (mm) 6

  • Flanges, 3D Print: Flange Height (mm) 3; Flange Angle (°) 15; Rim Radius (mm) 4; Top flange as separate part: no

  • Add Print Supports: Nozzle Dia. (mm) 0.4; Max Spacing (mm) 5; Air Gap (mm) 0.2

Licence: CC BY 4.0. Credit "CheapCADTools" when you share it.

Tagi