1 / 5
SK120 DIN Rail Enclosure – DC Buck-Boost Converter with CV/CC — zdjęcie 1
1 / 5

SK120 DIN Rail Enclosure – DC Buck-Boost Converter with CV/CC

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Two-part enclosure for the SK120 converter, with front control access and mounting for a separate 35 mm DIN rail clip.

Ocena
0 / 5
Polubienia
4
Pobrania
5
Wydruki
1
Wyświetlenia
96
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Compact. Practical. Ready to Mount.

I designed this two-part enclosure to mount an SK120 DC buck-boost converter neatly on a 35 mm DIN rail.

The enclosure houses the converter while keeping its display, adjustment dial, and buttons accessible. The module’s CV (constant voltage) and CC (constant current) settings remain accessible through its original front panel.

Features

  • Front opening for the SK120 display and controls

  • Separate main body and removable rear cover

  • Rear mounting provision for a separate 35 mm DIN rail clip

  • Two rear cable openings for input and output leads

  • M3 screws and threaded inserts for closing the enclosure

  • M4 screws and threaded inserts for attaching the DIN rail clip

Included Files

  • Adjustable Power supply enclosure top.stl: Front/main body, approximately 90 × 70 × 50 mm

  • Adjustable Power supply enclosure bottom.stl: Rear cover, approximately 90 × 70 × 4 mm

The filenames use “top” and “bottom”; when assembled, these form the front body and rear cover.

The converter, DIN rail clip, screws, threaded inserts, and wiring are separate components—not included in the STL files.

Hardware Required

  • 1 × SK120 converter matching the version shown in the photos

  • 1 × spring-loaded 35 mm DIN rail clip with a matching mounting pattern

  • 4 × M3 screws and 4 × M3 threaded inserts

  • 3 × M4 screws and 3 × M4 threaded inserts

  • Suitable input and output wiring

Choose screw and insert lengths that fit the printed pockets without protruding into the electronics or wiring.

Printing Suggestions

These are suggested starting points:

  • Material: PETG for functional use; see Prusa’s PETG guide

  • Layer height: 0.2 mm

  • Walls: 3–4 perimeters

  • Infill: 20–30%

  • Main body: Front face on the bed, open rear facing upward

  • Rear cover: Print flat, with insert recesses facing upward

  • Supports: Check the slicer preview and add where required

Check your SK120 panel dimensions and DIN clip mounting pattern before printing. Fit may vary between module versions and printer tolerances.

Assembly

  1. Install the M3 inserts in the main body and M4 inserts in the rear cover before fitting the electronics.

  2. Fit the SK120 into the front opening.

  3. Route the input and output leads through the rear cable openings.

  4. Attach the DIN rail clip using the M4 screws.

  5. Close the enclosure using the M3 screws.

  6. Mount the assembly on the rail and check that the controls and clip operate freely.

Keep the module’s cooling path clear and check its temperature under your intended load.

About This Design

I created this enclosure to keep the SK120 mounted neatly alongside my other DIN rail equipment.

If you print one, I’d love to see your setup!

Designed by TD Circuits.

Happy printing!

Tagi