Large Cat House Kit – 52 x 52 cm Floor, Two Arched Doors, Flat-Top Perch, Prints on 220 mm Beds
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Tool-free cat house kit: 52 x 52 cm floor (COMPACT 46 x 46 cm), two arched doors, flat top designed as a perch.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 3
- Wydruki
- 0
- Wyświetlenia
- 50
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Pets
- Licencja
- Creative Commons — Attribution — Noncommercial
A covered indoor cat house that you print in parts no larger than 200 x 200 mm and put together by hand, with no glue, screws, magnets, zip ties or tools, into a house much larger than your print bed. Four L-shaped corner piers stand on a ring of plinth trays, flat wall panels slide down between them, two faces have arched doorways, and a flat lid of nine pieces sits on top as one unit and forms a flat top designed as a perch. A porcelain or natural-stone floor tile that you buy locally rests on the plinth and is both the floor and the ballast. Two sizes of one design: LARGE (520 x 520 mm floor) and COMPACT (460 x 460 mm floor). It builds one house; it is not a stackable or expandable module system.
Validation status (please read): digitally validated only: CAD geometry and interface checks, slicer checks without supports, and stiffness and tipping calculations. It has not been physically printed or tested, with or without a cat: the fit of the joints on your printer, the roof's behaviour under a cat, the lid detents and long-term durability are all unverified. Print the two fit coupons first. All pictures are 3D renders of the CAD model, not photos.
Features
Floor 520 x 520 mm (LARGE): takes a standard 50 x 50 cm cushion or a 20 in (508 mm) round bed. COMPACT: 460 x 460 mm, takes a 45 x 45 cm cushion.
Two arched doorways on two different faces that you choose, each 190.5 mm wide with fully rounded edges on the jambs, sill and arch, so the cat has a second way out.
Flat top designed as a perch: nine lid pieces lock into one tray on hidden ribs. Roof stiffness calculated, not load-tested; no weight rating.
Tool-free: the lid lifts off in one piece by hand (pull up at two diagonal corners using the finger scoops at the pier tops), the wall panels slide out, and the lid pieces release by hand from the underside, so you can take the lid apart or change the door faces.
Every part is a separate print no larger than 200 x 200 mm, so a scratched or damaged part can be reprinted and swapped.
Closed panels, smooth on both faces: wipe-clean inside and out.
A notch in a plain plinth side tray lets a heat-pad cord up to 4.5 mm thick leave the house.
Designed to print without supports (checked in the slicer).
Sizes
LARGE | COMPACT | |
|---|---|---|
Outer size | 534 x 534 x about 400 mm | 474 x 474 x about 313 mm |
Interior floor | 520 x 520 mm | 460 x 460 mm |
Clear height from the tile top | 325 mm under the ribs, 375 mm at the centre | 255 mm under the ribs, 290 mm at the centre |
Doorways | 190.5 mm wide (180 mm at the arch springing), 285 mm from the sill to the arch crown | 190.5 mm wide (174.7 mm at the arch springing), 233 mm to the arch crown |
Sill above the tile top | 34 mm | 25 mm |
Floor tile (required, not printed) | 495-502 mm square, at least 5.6 kg | 445-450 mm square, at least 4.1 kg |
Filament (PETG, per-part settings) | 3 935 g | 2 765 g |
Print time (slow generic profile) | about 258 h | about 185 h |
A cushion takes about 60 mm of the clear height. A large cat can lie, curl and turn inside LARGE; a large Maine Coon cannot stand with its head up, and whether your cat can sit upright under the ribs depends on the cat: measure it sitting. As a rough size guide only, not a load rating: LARGE for cats up to about 10 kg, COMPACT for cats up to about 6 kg. If your cat is average-sized, a bought cat house is usually cheaper and faster than printing COMPACT.
Printer: at least 200 x 200 mm usable bed and 216 mm Z (220-256 mm class printers); the largest part is 200 x 200 mm and the piers are 199 mm tall.
What you also need (not printed)
Floor tile (required): porcelain or natural stone only, of the size and minimum mass above; in practice 10-12 mm porcelain or stone for LARGE and 9-12 mm for COMPACT (12 mm is the most that fits). Sizes sold as "50 x 50 cm", "20 x 20 in" or "45 x 45 cm" are nominal: measure the actual tile, and weigh it on a bathroom scale. A US 18 x 18 in tile (457 mm) does not fit COMPACT. Uncut (as-supplied) or eased edges. Tiles are often sold only by the box.
Underlay (required): a thin, flat, non-slip underlay larger than the footprint (waterproof if your floor is sensitive to liquid).
Recommended: a liner 515 x 515 mm (LARGE) / 455 x 455 mm (COMPACT) with a waterproof backing and a 30 mm upturned hem; a cushion 50 x 50 cm / 45 x 45 cm; a perch pad 440 x 440 mm / 380 x 380 mm, 10-15 mm wool felt with a non-slip backing. Optional: a thermostatic pet heat pad.
Which files?
Easiest: the ready-to-print PrusaSlicer projects (PrusaSlicer 2.9 or newer). Per size three projects, in print order, with every part oriented, counted, placed and set up with its per-part settings; each bed was sliced to check it. Open a project, select your printer preset (laid out for a 220 x 220 mm bed; on another bed size use Arrange if parts end up off the beds), slice all beds and print.
Project | Beds | Contents | About (slow generic profile) |
|---|---|---|---|
cat_house_large_1_plinth_and_fit_coupons | 6 | 2 fit coupons, 4 corner trays, 2 door-sill trays, 2 side trays, 4 jamb beads | 452 g, 32 h |
cat_house_large_2_piers_and_walls | 6 | 4 piers, 2 wall panels | 1052 g, 73 h |
cat_house_large_3_lid | 9 | 4 lid corners, 2 plain + 2 arched edge pieces, 1 keystone | 2482 g, 158 h |
cat_house_compact_1_plinth_and_fit_coupons | 6 | as LARGE 1 | 333 g, 24 h |
cat_house_compact_2_piers_and_walls | 6 | 4 piers, 2 wall panels | 917 g, 66 h |
cat_house_compact_3_lid | 9 | as LARGE 3 | 1556 g, 98 h |
cat_house_compact_option_den_panel | 1 | den panel (COMPACT only; print it instead of one wall-panel bed) | 64 g, 4 h |
If you switch to your own PETG filament preset, set the lid cooling again for the lid project and the coupon bed (see Print settings): a filament preset replaces the project's cooling values. The STL files (cat-house-large_* / cat-house-compact_*; each file name says the part and how many to print) carry geometry only: with them or another slicer, set the per-part settings below yourself.
Den option (COMPACT only): a wall panel with a 169 mm clear round opening with a fully rounded edge, instead of one solid wall panel; cats will use it as a third doorway. Not offered for LARGE (the opening is smaller than a large-cat passage). Door faces: any two different faces; the part files are the same, you choose where the arched lid pieces, the door-sill trays and the jamb beads go.
Parts per house: 4 plinth corner trays, 2 plain side trays with a cord notch, 2 door-sill trays, 4 corner piers, 2 wall panels (COMPACT den option: 1 wall panel + 1 den panel), 4 jamb beads, 4 lid corners, 2 plain and 2 arched lid edge pieces, 1 keystone = 27 parts, plus 2 fit coupons to print first.
Print settings
Material: PETG for every part, matte finish recommended, one colour from one batch where possible. Not PLA or PLA-based specialty filaments (many wood-fill and silk filaments are PLA-based; PLA softens around 55-60 °C and is brittle), not ASA. No fuzzy skin (it traps hair).
Nozzle / layers: 0.4 mm, 0.20 mm. No supports.
Per-part settings: plinth trays 2 perimeters + 7 % gyroid (3-4 perimeters if accidents are likely); piers 2 perimeters + 7 % gyroid (3 perimeters for hard scratchers, about 50-60 g more per pier); wall and den panels 2 perimeters + 10 % gyroid with 6 bottom layers; lid pieces 2 perimeters + 8 % grid with 6 top and 6 bottom layers; jamb beads 4 perimeters + 40 %. A generic default profile uses far more filament.
Lid pieces and fit coupons: slow down short layers (minimum layer time 15 s, minimum print speed 4 mm/s) and keep the part fan near your PETG profile's normal maximum (about 50 %): stronger cooling weakens the flexing detent tongues and fins. Switch back for the other parts.
Orientation: plinth trays flange-down; piers standing (5 mm brim recommended, remove it completely); wall panels and the den panel outer face down (a textured PEI sheet gives a matte outer face); lid pieces perch face down; jamb beads as oriented in the files. Use a brim or mouse ears on large flat parts if your PETG lifts (a 5 mm brim on a 200 x 200 mm wall panel needs a 210 mm bed).
Colour: one matte colour, or the plinth trays darker and everything else in one lighter colour. Do not print the lid pieces in different colours.
Assembly (no tools)
Fit coupons first. The tongue pieces should slide together by hand without forcing and without play; the lid rib splice needs firm pressure. The part files have fixed clearances: if a coupon is too tight or too loose, calibrate flow and elephant-foot compensation and reprint the coupon before printing the large parts. The coupon's detent tongue prints with longer layer times than the tongues on a lid corner, so it checks the fit, not how well your printer prints those tongues: use the lid cooling settings.
Lay the underlay on a flat floor. Stand the 4 corner trays on it and, keeping them slightly apart, drop the 4 side trays onto their tongues (door-sill trays on the two door faces, notched plain trays on the other two), then push the trays together until every seam closes onto its hidden stop (the seams stay narrow and even, about 0.5 mm). Route a heat-pad cord through a notch now, never under the tile or the plinth.
Lay the floor tile onto the flange ring; the ribs centre it.
Lower each pier onto its corner tray slightly toward the outside corner so the hook tenons enter the slots in its foot, then slide it into line until it stops. Put the lid on soon: until then a pier pushed sideways can slide back off its hooks.
Slide the wall panels down the pier sockets and fit the two jamb beads in each door bay.
Lid, on the house: set the 4 lid corners on the piers and press down until the detents click; press in the 2 plain and 2 arched edge pieces (arched ones over the doors) until their fins click and the top is flush; press the keystone in. Press over the ribs, not mid-panel. If an edge piece sits high, check that the plinth seams are closed and the lid corners fully down, then push its two lid corners toward each other while you press it in; do not force it.
Fit the liner (hem up over the gap between the tile and the rim), the cushion and the perch pad. Check that both doorways are clear.
Cleaning and moving
Weekly: pull the liner and cushion out through a door and wash them; wipe the tile and the inside faces you can reach.
Deep clean (cat out of the house): hold the plinth down with a foot and pull straight up at two diagonal corners, using the finger scoops at the pier tops, until the detents release; lift the lid off level (a helper makes the LARGE lid easier). The detents need a firm pull (by calculation about 2-4 kg-force per hand for LARGE, untested). Lift only at the corner scoops: never push the ceiling up from inside and never lift by an edge piece or the keystone. If the lid tilts and sticks on the pier tenons, lower it, level it and lift again. Wipe or shower-rinse the lid upside down; slide the wall panels and jamb beads out to wash them. When you put the lid back, keep fingers and paws clear of the seams and press the corners down until the detents click.
Hand wash only: warm soapy water, do not soak or submerge the parts (the closed hollow parts can take in water), let them dry before reassembly. Diluted bleach only after washing off urine with soap and water, then rinse; never mix bleach with ammonia-based or other cleaners. No dishwasher, no alcohol or vinegar soaks, no ammonia cleaners. The effect of enzymatic cleaners on printed PETG is untested; rinse after use.
To take the lid apart: keystone first. Push each of its two hanging fins away from its rib only until it clears (about 1 mm; the fins have no stop) and push the keystone out toward the perch side, then release the edge pieces' fins through the opening the same way.
Moving: slide the house on its underlay, pushing low at the plinth. Never lift or carry it by the lid or the perch. To move it further, take it apart; with the lid, walls and piers off, lift the tile out with a suction tile lifter (suggested method, not tried on a printed house).
Use and safety
For adult cats; indoor use only. Not for rabbits, guinea pigs, hamsters, gerbils, degus, rats, mice or any other rodent, chinchillas, ferrets, reptiles, birds, or dogs and puppies: these animals gnaw or swallow plastic, which can cause serious injury or intestinal blockage.
Pica: if your cat chews or eats plastic, fabric or other non-food items, do not use this house.
Kittens: supervise them; the openings and gaps are sized for adult cats.
Children: not a seat, step or toy; children must not climb or sit on the house.
Inspect before every use: check for cracks, loose or missing parts, sharp edges and a lid that is not seated. Stop using the house and reprint any cracked or damaged part.
Keep both doorways clear of walls and furniture so the cat always has a second way out.
Do not stack houses and do not put heavy objects on the perch.
Small parts: keep the fit coupons, brims and any spare or broken pieces away from pets.
Build it correctly: PETG only, the stated per-part settings, fully assembled with the tile in place, on a flat hard floor on an underlay (on carpet, put a flat rigid board larger than the footprint under the underlay).
Heat pads: thermostatically controlled pet heat pads only (about body temperature), placed to one side so the cat can move off them; lead the cord through a plain side-tray notch (up to 4.5 mm) or over a door sill, never under the tile or the plinth, never force it into the notch, check it for pinching after the cat has used the house, and prefer low-voltage pads with chew-resistant cords. Keep the house out of direct sun behind glass and away from radiators and heat lamps.
Material: you make the parts from filament you choose; no claim is made that the printed material is non-toxic or food-safe.
Supervise the first use; many cats take days to accept a new hideout.
Limitations
Not physically printed or tested (see Validation status). All values come from CAD, digital checks and calculations.
Roof: stiffness calculated, not load-tested; no weight rating. By calculation the LARGE roof deflects about 1.9 mm under a 118 N design point load (a 12 kg design cat standing at the centre) and COMPACT about 1.5 mm under 59 N. These are design inputs, not ratings. Long-term creep of PETG under a cat sleeping on the perch was not assessed. Joint strength and long-term durability are untested.
Tip resistance depends on the tile mass. By calculation, pulling sideways at the roof edge needs about 62 N (about 6.4 kg-force) for LARGE and 51 N (about 5.2 kg-force) for COMPACT with a minimum-mass tile, but only about 26 N / 20 N without a tile. The minimum-mass tile only just meets the design's provisional sideways-pull criterion; for cats over about 8 kg use a heavier LARGE tile (7 kg or more; weigh it). Tipping when a cat lands fast near the edge of the perch has not been evaluated. Never use vinyl, foam, cork, carpet or light ceramic tiles, or a board instead of the tile, and never use the house without its tile.
Plastic: claw marks will show; deep scratches can open a panel's hollow core (reprint the part); layer lines are visible on the standing parts.
Spills can reach the floor: liquid can run under the tile and out through the plinth seams and the cord notch. Keep the liner hem over the gap, use a waterproof underlay on floors that liquid would damage, and if urine gets under the liner, take the house apart and wash the tile and plinth trays (replace any tray that keeps smelling).
Do not put felt pads, glides or feet under the plinth rim: they lift the flange that carries the tile. Use an underlay under the whole house.
Doors are 190.5 mm wide, narrower than some commercial large-cat doors, and the clear height is lower than in many furniture-style cat houses. Measure your cat.
Changing the door faces later means taking the house apart, including lifting the tile out to swap the sill trays. The tile has only a few millimetres of clearance to the rim.
Cost: filament, the tile and the textiles together cost about as much as a mid-range commercial cat house, and LARGE takes about 258 hours of printer time on the slow generic profile (faster printers and profiles need less). Print it for the kit, the washable panels and the replaceable parts, not to save money.
Pictures
All pictures are 3D renders of the CAD model or drawings made from it, not photographs: a lifestyle render in a room corner (cover), the interior with a 50 x 50 cm cushion (cut away), a low view through a doorway in a staged room, the lid lifted off in one piece, an exploded view of the 27 parts, a dimension card, both sizes side by side, colour options, a clean studio view, the closed rear faces and size-guide drawings for both sizes (the sill heights in the size guides are measured from the floor; above the tile top they are 34 mm for LARGE and 25 mm for COMPACT). Cushions, pads, tiles and rooms are stand-ins; there is no cat in any image.