1 / 1
Poinsettia Clay Cutter & Stamp Set for Pottery: Layered Christmas Flower — zdjęcie 1

Poinsettia Clay Cutter & Stamp Set for Pottery: Layered Christmas Flower

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Three clay cutters with matching vein stamps that make a layered poinsettia ornament.

Ocena
0 / 5
Polubienia
5
Pobrania
18
Wydruki
0
Wyświetlenia
69
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial

A set of cutters to make layered poinsettia flowers in clay: Christmas ornaments, hanging decorations, gift tags, and appliqués for plates, mugs and wreaths.

Can be used for cookies as well.

What's included

  • Large bract cutter (70 × 68 mm) and its vein stamp.

  • Small bract cutter (50 × 52 mm) and its vein stamp. When you stack the layers, the small bracts sit between the large ones.

  • Centre button cutter (21 × 20 mm) and its stamp, which presses five little rings for the flower buds.

Every cutter has a 5 mm hole punch in the middle, so all three layers line up on one cord or wire. The bract stamps press a midrib with curved side veins into every bract.

Sized for clay shrinkage

My clay shrinks roughly 11-12% from wet to fired, so the final size is about:

Piece

Cut size

Fired size (about)

Large bracts

70 × 68 mm

62 × 60 mm

Small bracts

50 × 52 mm

45 × 46 mm

Centre button

21 × 20 mm

18 × 18 mm

If your clay body shrinks more or less, scale the models in your slicer to suit.

How to use

  1. Roll clay to an even slab, about 4-6 mm thick.

  2. Lay the stamp on the clay, pattern side down.

  3. Place the cutter over it so the stamp sits inside the outline. The punch tube passes through the hole in the stamp. Press down to cut. Dusting the cutter with cornflour helps with sticky clay.

  4. Hold the stamp down with your fingers and lift the cutter off.

  5. Press the stamp firmly to imprint the veins, then lift it straight up.

  6. Repeat for the small bracts and the centre button.

  7. Stack the layers: large bracts at the back, small bracts turned so they sit between the large ones, centre button on top. Line up the holes. Score and slip between the layers if you want them joined, or fire them separately and thread them on a cord.

  8. Smooth the edges with a damp sponge or finger, dry slowly, then bisque, glaze and fire as normal.

Print notes

  • I printed on an Elegoo Centauri Carbon, 0.4 mm nozzle.

  • PETG (Elegoo Rapid PETG), 0.2 mm layers.

  • I printed the cutters flange-down (wide rim on the bed, cutting edge pointing up). No supports needed.

  • I printed the stamps flat on their backs with the pattern facing up. No supports needed.

  • Minimum wall is 0.8 mm (two perimeters), so keep wall loops at 2 or more.

  • The included .3mf has all six parts laid out on one plate for a 256 × 256 mm bed. Individual STLs are included for other printers and slicers.

  • PETG handles water and washing up better than PLA, but avoid the dishwasher. Rinse and let the tools dry.

Matching sets

This goes with my holly leaf and sprig set: 

About me

I'm a hobbyist potter and made these for my own Christmas pieces. You can see the finished work at my pottery page: https://www.instagram.com/mudonmynose

If you print these and try, please let me know, and I would really appreciate a a Make with a photo of your poinsettias. I'd love to see them!

Tagi