Gyroid Ball Christmas Ornament
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A 65 mm bauble cut from a gyroid, one smooth wall winding through two interlocked labyrinths
- Ocena
- 0 / 5
- Polubienia
- 2
- Pobrania
- 22
- Wydruki
- 1
- Wyświetlenia
- 75
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Winter & Christmas & New Year's
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
It looks like lace, but it is one single curved wall. A gyroid is a surface that winds through space without ever crossing itself and splits it into two separate, interlocked labyrinths of tunnels, each the mirror twin of the other. Cut to a sphere, it becomes a bauble you can look straight into, and in a silk or metallic filament every curve catches the tree lights.
Maths fact: Alan Schoen found the gyroid in 1970 while working for NASA. It is a minimal surface, like a soap film: at every point it curves up one way exactly as much as it curves down the other. It contains no straight lines and no flat patches, it repeats forever in all three directions, and it turns up in nature, in butterfly-wing scales and in some cell membranes. 3D printers use it as infill because it is strong in every direction.
How it was made: we generated the ball with Curiosa Shapes, the parametric shape tool for 3ds Max that Curiosa Tools is building. It builds the gyroid from its formula (sin x cos y + sin y cos z + sin z cos x = 0) as a 1.6 mm wall around the exact surface, with 22 mm cells, cut to a 65 mm sphere and closed where it is cut, as one watertight solid. We then cut a small 1.5 mm flat on top, added a flush eyelet with a 2.5 mm hole there, and checked the file layer by layer for a 0.4 mm nozzle. Curiosa Shapes is in development; you can see it, and try the shape engine in your browser, at https://curiosa.tools/?via=pr
It is 65 mm across. It hangs flat side up: the small flat and the eyelet face the branch, so you do not see them. The eyelet's hole runs straight through into the gyroid's own tunnels, so a thread or fishing line goes in through the eyelet and comes out of the openings on both sides, then up to a knot, like a bead (a needle helps). The hole is 2.5 mm: thread, fishing line or a thin cord, not ribbon. It hangs straight, with the centre of mass right under the hole.
The pictures are renders of the exact model file.
Files
- gyroid-ball-ornament-65mm.stl - the ornament, one closed solid, ready to slice (standing on its flat)
Made with Curiosa Tools - https://curiosa.tools/?via=pr
**Print settings (PLA):**
- **Material:** silk silver PLA (the pictures) or silk gold PLA: the shiny, slightly metallic silk filaments make the curves sparkle. Plain PLA works too.
- **Silk PLA needs:** slower outer walls (about 60 to 100 mm/s instead of 200) and the nozzle 5 to 10 °C hotter than plain PLA (about 220 to 230 °C), or follow the spool's label. Silk is weaker between layers, so peel supports off gently.
- **Orientation:** as the file is: standing on its small flat, eyelet down on the bed. That flat becomes the top when it hangs.
- **Supports: yes, tree (auto) supports from the build plate only, with a low threshold angle:** **5° in Bambu Studio**, 15° in OrcaSlicer. The two slicers read the threshold differently: in Bambu Studio 15° or the default 30° still supports almost the whole lower half (about 58 g, 3 h 30 min on an A1), while 5° gives the same light supports as OrcaSlicer at 15°. A ball standing on a small flat (about 20 mm across, mostly open lattice) has a steep underside, and a layer-by-layer check finds three tiny floating starts (about 1 mm² each) where a lattice wall begins at its lowest point on the outside of the sphere. These light tree supports touch only the outside of the lower half and are about 2 to 3 g. Without supports the slicer warns of floating regions.
- **Brim:** 5 mm. The ball touches the bed only over 154 mm² (the eyelet disc and the lattice around it), so the brim keeps it stuck down.
- **Layers and walls:** 0.2 mm layers, 2 walls, 15 % infill. The 1.6 mm wall is four line widths of a 0.4 mm nozzle, so the lattice prints as solid wall.
- **Weight and time:** about 43 g and 2 h 20 min with supports and brim in Bambu Studio for a Bambu Lab A1 (0.4 nozzle, 0.20 mm Standard, Bambu PLA Silk); about 40 g and 2 h 24 min in OrcaSlicer 2.4.2 for a P1S with Bambu PLA Basic. These are slicer estimates, not a measured print.
- **Slicer warnings:** none with the supports above (checked in Bambu Studio and OrcaSlicer).