1 / 4
Terarium — zdjęcie 1
1 / 4

Terarium

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

PL: Terrarium 3D (PETG), drzwi z plexi 3mm, bolce. EN: 3D printed PETG terrarium, 3mm acrylic door.

Ocena
0 / 5
Polubienia
1
Pobrania
1
Wydruki
0
Wyświetlenia
50
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Pets
Licencja
Creative Commons — Attribution — Noncommercial

📐 Wymiary i elementy przezroczyste (ok. 3 mm)

  • Jako wypełnienie ścianek (boki, tył oraz front) możesz użyć pleksi, zwykłej szyby lub innego przezroczystego materiału o grubości około 3 mm.

  • Wymiary: Najlepiej dokładnie zmierzyć szczeliny montażowe suwmiarką bezpośrednio na wydrukowanym modelu, aby przyciąć materiał idealnie pod swój egzemplarz. W projekcie uwzględniono odpowiedni luz technologiczny, który pozwala na wygodny montaż wszystkich tafli oraz zastosowanie warstwy silikonu, kleju lub uszczelniacza.

  • Drzwi frontowe: Przednia szyba/pleksi jest dłuższa niż pozostałe ścianki, dzięki czemu po zamontowaniu tworzy funkcjonalne drzwiczki do terrarium.

⚙ Zalecenia dotyczące druku 3D (Slicer Settings)

  • Supporty (Wsporniki): Konieczne jest włączenie wewnętrznych supportów w slicerze (np. drzewiaste / organic supporty), aby poprawnie podeprzeć zwisy i elementy konstrukcyjne pod ramę drzwi.

  • Orientacja: Model należy drukować w takiej pozycji, w jakiej został zaprojektowany.

  • Wypełnienie (Infill): Minimum 15–20% (zalecany wzór Grid lub Gyroid), aby zapewnić odpowiednią sztywność obudowy.

  • Liczba obrysów (Walls/Perimeters): Minimum 3-4, co zagwarantuje szczelność ścianek i trwałość prowadnic.

🛠 Instrukcja montażu i składania

  1. Czyszczenie wydruku: Po zakończeniu druku ostrożnie usuń wszystkie wewnętrzne supporty.

  2. Sklejanie i dopasowanie korpusu:

    • Górna część terrarium (góra) posiada specjalnie zaprojektowane otwory oraz bolce naprowadzające, które ułatwiają idealne i równe spasowanie jej z resztą korpusu przed ostatecznym sklejeniem.

    • Do łączenia elementów wydrukowanych z filamentu PET-G użyj sprawdzonego kleju do tworzyw sztucznych (lub cyjanoakrylowego/epoksydowego w kontrolowanych ilościach).

  3. Montaż przeszklenia i drzwi:

    • Boczne i tylne tafle wklej lub uszczelnij w dedykowanych ramach, wykorzystując luz technologiczny pod silikon.

    • Dłuższą przednią taflę zamontuj jako drzwi, korzystając z przygotowanych prowadnic i kołków naprowadzających.

  4. Ważne – bezpieczeństwo zwierzęcia: Po zakończeniu montażu i uszczelniania odczekaj odpowiedni czas, aż klej całkowicie wyschnie i wywietrzeją wszelkie opary. Dopiero gdy wnętrze będzie całkowicie neutralne zapachowo i bezpieczne, wprowadź do terrarium swojego pupila.

  5. Here is the text translated into clear, natural English for Printables:

    📌 Summary (Short Description)

    Custom modular terrarium designed for small invertebrates, spiders, or praying mantises. Built with PETG, this design combines a 3D-printed frame with four transparent panels (approx. 3 mm thick), where a longer front panel serves as a functional door. The model features alignment pins and matching holes for precise assembly, as well as calculated tolerances to allow sealing with silicone or glue.

    📝 Full Description

    📐 Dimensions & Transparent Panels (approx. 3 mm)

    • You can use acrylic (plexiglass), glass, or any other transparent sheet material with a thickness of roughly 3 mm for the side, rear, and front panels.

    • Dimensions: We recommend measuring the mounting slots on your finished 3D print using digital calipers to cut your sheets to exact dimensions. The model includes an extra tolerance buffer so panels fit comfortably and leave room for a layer of silicone, glue, or sealant.

    • Front Door: The front acrylic/glass panel is longer than the side panels, allowing it to function as a full-length door for easy access inside.

    ⚙ Recommended 3D Print Settings

    To ensure a smooth print, use the following slicer settings:

    • Supports: Internal supports MUST be enabled in your slicer (organic/tree supports work best) to properly hold up internal overhangs and features around the door frame.

    • Orientation: Print the parts in the orientation provided in the STL/STEP file.

    • Infill: Minimum 15–20% (Grid or Gyroid patterns recommended) for solid structural rigidity.

    • Walls/Perimeters: Minimum 3–4 perimeter lines to guarantee strength along the track edges and frame joints.

    🛠 Assembly Instructions

    1. Post-Processing: Carefully remove all internal support structures after printing.

    2. Aligning & Gluing the Frame:

      • The top section (góra) features built-in alignment pins and corresponding holes to guide exact positioning onto the main frame before gluing.

      • For bonding PETG parts, use a dedicated plastic adhesive, cyanoacrylate (superglue), or two-part epoxy in controlled amounts.

    3. Installing Glass/Acrylic Panels & Door:

      • Slide/fit the side and back panels into their slots, sealing them with silicone using the built-in tolerance gap.

      • Install the longer front panel into the door guides using the provided alignment pins/tracks.

    4. Important Safety Notice: After gluing and sealing, allow sufficient time for all glues, adhesives, and silicone to fully cure and off-gas. Only introduce your pet once the interior is completely scent-free, non-toxic, and dry.

Tagi