1 / 1
Porsche 911 (996) Cabriolet Line Art — zdjęcie 1

Porsche 911 (996) Cabriolet Line Art

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Side-profile line art of the Porsche 911 (996) Cabriolet with the top down. Made with AI help.

Ocena
0 / 5
Polubienia
1
Pobrania
7
Wydruki
0
Wyświetlenia
36
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Wall-mounted
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Porsche 911 (996) Cabriolet line art

A side-profile line drawing of the 996-generation 911 Carrera Cabriolet, top down and headrests up. It is one connected piece, so it prints flat in a single go and hangs like a metal wall-art sign.

The lower body (wheel arches, door, sill, bumpers, lights and mirror) is based on https://www.printables.com/model/813734-porsche-996. I redrew the cabrio parts for the open car: the shorter windshield frame, the headrest, the folded top and the rear deck.

Size

  • 250 × 68.7 × 2 mm

  • Lines are about 1.5 mm wide

  • Fits a 220 × 220 mm bed when rotated about 45° (that's how I printed it on an Ender-3 V3 SE)

Print settings

Tested on a Creality Ender-3 V3 SE, sliced in Cura 5.13 from the stock "Low Quality" profile.

  • Material: PLA, 200 °C nozzle, 60 °C bed

  • Nozzle: 0.4 mm

  • Layer height: 0.28 mm (7 layers)

  • Walls: 2 (0.8 mm)

  • Top/bottom layers: 4 each, so the piece prints solid

  • Top/bottom pattern: Concentric, initial layer too

  • Z hop when retracted: on, 0.2 mm (Cura's Creality profiles then switch combing off)

  • Retraction: 0.8 mm at 40 mm/s

  • First layer speed: 15 mm/s, ramping up over 3 layers

  • Supports: none

  • Adhesion: skirt, no brim

  • Print time: about 45 min, 2.8 m of filament (about 8.5 g)

The setting that matters: Z hop

With Cura's default combing, every travel move follows the thin lines that are already printed. On this model that adds up to about 7 m of travel per layer, with the nozzle dragging over fresh plastic the whole time. Turning on Z hop makes the travel moves straight and lifted. That cuts travel moves per layer from about 2,500 to 250 and makes the print roughly 15% faster.

The concentric top/bottom pattern replaces the zigzag fill in the small triangles where lines meet, so those spots print cleanly.

Tips

  • Clean the bed with isopropyl alcohol. Thin lines need a good first layer; use glue stick if ends lift.

  • Let the bed cool before you peel the print off so the thin lines don't bend.

  • To resize, scale X and Y only and keep Z at 2 mm. Below about 80% the lines get thinner than 1.2 mm and turn fragile.

  • Mount it with double-sided foam tape, mounting putty or small removable adhesive strips.

  • Pick a filament that contrasts with the wall: black on a light wall, white or silver on a dark one.

Fan art. Not affiliated with or endorsed by Porsche AG.

Tagi