1 / 4
Halloween Spirit Board Spinner - Fortune Telling Fidget Toy — zdjęcie 1
1 / 4

Halloween Spirit Board Spinner - Fortune Telling Fidget Toy

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Flick the staring-eye planchette and this clicking spirit board spins out your fate. A secret lever rigs DOOM.

Ocena
0 / 5
Polubienia
14
Pobrania
34
Wydruki
0
Wyświetlenia
210
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

This is an antique spirit board that answers your questions. Ask your question, flick the staring-eye planchette and it spins with loud clicks, slows down and lands on your fate: YES, NO, SOON, NEVER, MAYBE, ASK AGAIN, BEWARE or DOOM. A hidden Fate Lever lets you secretly rig the answer to DOOM to prank your friends.

 

The board is 100 mm across and about 15 mm tall. Its raised gothic border carries crescent moons, stars and tiny bats. The eight answer zones are lettered in a gothic typeface and split by raised dividers. Inside the band you find a sun face and a moon face in the upper corners, an engraved star field, a filigree ring and a dial ring around the hub. The planchette is a teardrop with a heavy-lidded staring eye: the hub head is the eye's slit pupil and the eye windows show the board underneath. It tapers to a sharp point that reads the answer. The underside is beveled so the board sits flat.

 

HOW IT WORKS

The planchette spins on a captive mushroom-head hub: a 45 degree countersink in the planchette sits under the conical head, so it spins freely but cannot come off. Under the planchette a thin S-curved flexible pawl rides on a ring of 24 teeth around the hub. Every tooth gives a click and a little drag, so the planchette slows down and stops at a random answer.

The Fate Lever is a small slider hidden in the rim at the ASK AGAIN zone, directly opposite DOOM. It runs in a dovetail-guided tunnel inside the board and has a small spring detent that clicks at both positions. Push the little ridged tab in by 3 mm and its tip moves into the tooth ring channel. A catch lug under the planchette's tail then always stops against it, which leaves the pointer on DOOM. Pull the tab back out and the board is fair again.

 

FILES (1)

Omenspin_PrintInPlace.step - print-in-place: board with hub, planchette with pawl, and the Fate Lever slider, three separate bodies with clearances.

 

PRINTER AND SETTINGS

Bed size: 101 x 101 x 15 mm. Nozzle 0.4 mm, layer height 0.2 mm, 3 walls, 4 top and 4 bottom layers, 15 percent infill, supports OFF, no brim. Material PLA. The first layer must be good and flat, but do not squish it hard (that can glue the planchette's seat to the board).

Estimated print time and filament: about 5 hours and 55 g.

 

PRINT ORIENTATION

Printed flat, board face up, exactly as the file imports. The planchette is printed pointing at YES.

 

COLORS

One color works because all the lettering and ornaments are deep relief. For the antique look, print the board dark and switch to gold or bone white at the layer where the lettering starts: insert a filament change (M600 or a pause) at Z = 9.2 mm, which is the first layer printed above the 9.0 mm board face (layer 46 at 0.2 mm layers when the first layer is 0.2 mm). Everything above it becomes the second color: border, lettering, dividers, the planchette and the hub head. The Fate Lever stays in the dark color and blends into the rim.

 

AFTER PRINTING (FREEING THE PARTS)

1. Hold the board and gently rock the planchette up and down, then twist it a little in both directions. It drops by 0.4 mm onto the hub seat and starts clicking.

2. Spin it a few times to wear in the pawl.

3. Push the Fate Lever tab in and out a few times until it clicks smoothly.

 

TIPS AND TROUBLESHOOTING

- If the planchette will not turn, it is usually a too-squished first layer or elephant's foot near the hub. Twist firmly but gently, or run a thin blade around the hub under the planchette.

- If the clicks are too soft, print in PLA rather than PETG or TPU; if the pawl feels too stiff, print the planchette with 2 walls.

- If the pointer does not stop on DOOM with the lever pushed in, check that the tab is fully in (it clicks) and flick a little softer.

 

CHANGES FROM THE ORIGINAL BRIEF (FOR PRINTABILITY)

- The Fate Lever slides a stop pin sideways into the tooth ring channel instead of raising a bump. A sideways stop is far more reliable in a print-in-place part than a vertical pop-up pin.

- The answer ring sits slightly outside the planchette tip so all lettering can be raised 1 mm without touching the pointer.

- The planchette is printed with a 0.8 mm air gap over the board (0.4 mm at the hub seat). After printing it drops onto the hub seat and floats 0.4 mm above the board, so only the hub touches it while spinning.

- The sun and moon faces are recessed (sunk relief) because the planchette sweeps over them.

Tagi