1 / 5
3D Printed Tape Dispenser, Paper Cutter, Hole Puncher, and Ruler! — zdjęcie 1
1 / 5

3D Printed Tape Dispenser, Paper Cutter, Hole Puncher, and Ruler!

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Essentials for any office job (Or in my case, a student)! The hole puncher and ruler goes in your binder!

Ocena
0 / 5
Polubienia
1
Pobrania
4
Wydruki
0
Wyświetlenia
22
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Gadgets
Licencja
Creative Commons — Attribution

School Supplies at an instant!

Have you ever been at school, and wanted your own hole puncher, ruler, paper cutter, or tape dispenser without waiting for it?
As someone who wants quick solutions, I feel this issue! This is why I developed those exact school supplies, and not only that, but they also fit in your binder!

Tape dispenser!

The tape dispenser is able to hold up to 0.75" width in tape, and makes it easier to dispense tape quickly! To cut the tape, use the following blade.

Paper cutter

We have ALL experienced times where we were told to make a cut, and we get an uneven line! This is why I made the paper cutter! You just insert your paper underneath, and hold down to cut!

Hole puncher

Since I joined high school, we relied in binders A LOT. However, binders require every page to have holes in it so it can go in the rings! A lot of the time, I just skip the step of putting holes, and let them rip to put it in. Instead of that, I made my own personal hole puncher that works just as well, and also goes in my binder, as the puncher itself is thin, and has holes to go in the binder!

Ruler

I always lose my ruler. Unfortunately, a lot of the time, it just sits at the bottom of my backpack rotting. My ruler expands and also has holes to go in your binder! (All measurements are in cm)

Assembly!

Want to make your own supply? Follow these steps! Keep in mind that when something is mentioned as "part _", it is labelled through the file names!

Make your own Tape Dispenser!

To make your own tape dispenser, you are going to need the following:

Item

Quantity

3D-printed parts!

1 of each part

Tape of your choice (Max 0.75 inches in width)

1

M3 8mm screws

2

Tape dispenser blade!

1 set from the provided link, 1 needed for the project

Use the following instructions:







Put the tape roll through
Part 1 in /tape dispenser








Add Part 1 and the tape roll to Part 2








Add part 3 to shut off the dispenser







Add the screws to secure the blade!

Make your own Paper Cutter!

Item

Quantity

3D Printed Parts!

Print the assembly together

Blade

1 blade

Super Glue

few drops from one tube





To make your own paper cutter, it is surprisingly simple! All you need to do is put part 2 through the mounts for the hinge in part 1, and use adhesive to attach part 3 to close off the hinge.









.. And add the blade!

The blade already has all the mechanics to press down, and only then will it cut.

Make your own Ruler!

The ruler is the most difficult part of this project! Getting all those measurements and getting the extrudes took a lot of repetitive work and a long time!

To make your own ruler, you need the following:

Item

Quantity

3D Printed parts

1 of each part

Super Glue

few drops from one tube






Add part 2's hole into part 1





Use the super glue to attach part 3 to part 1 and 2! Make sure that the side of the measurements is facing OPPOSITE to the measurements of part 2.

Make your own hole puncher!

To make your own hole puncher, you just need the 3D-printed parts!





Simply 3D Print the assembly! You don't print it in 2 pieces. 

Future improvements!

In the future, to improve this project, I want to mainly improve on the hole puncher project by making the project printable in 2 seperate parts!

Tagi