1 / 13
Looki L1 camera mount v9: snug holder + slide-in collar clips (ABS) — zdjęcie 1
1 / 13

Looki L1 camera mount v9: snug holder + slide-in collar clips (ABS)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

v9: snug holder for the bare Looki L1 + thick/thin collar clips that slide in on dovetail rails and click locked.

Ocena
0 / 5
Polubienia
0
Pobrania
2
Wydruki
0
Wyświetlenia
7
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Photo & Video
Licencja
Creative Commons — Attribution

v9 IS OUT (Oct 26 2026): a new snug holder and two slide-in collar clips. These are the files to print now.

CHANGELOG

- v9 (Oct 26 2026): new holder + clips; lanyard frame coming later.

- v4 (Oct 20 2026): the original cradle + clip. Its files and notes are kept below.

V9 FILES (CURRENT / RECOMMENDED)

- looki_v9_holder.stl: the holder. The pocket is sized for the bare Looki L1 (no silicone case) with 0.25 mm per side, and 4 snap bumps (0.6 mm over the edge, just above the widest rim) hold it in. Lens, button and back windows stay open.

- looki_v9_clip_thick.stl (32 mm wide) and looki_v9_clip_thin.stl (26 mm wide): pick the one that fits your collar.

- looki_v9_abs_profile.ini: the PrusaSlicer profile the v9 parts in the photos were printed with.

HOW THE CLIP LOCKS

- The clip slides into a channel across the back of the holder from the right side. Dovetail rails at the top and bottom run the clip's full width, and the closed left end is the stop.

- A small button on a flex beam clicks into a 4.2 mm hole in the holder. The weight sits on the rails, not the button.

- To remove: press the thumb tab toward the shirt and slide the clip out to the right (or push the button from inside with the Looki out).

V9 PRINT SETTINGS

- Material: ABS, 240 C nozzle / 100 C bed.

- 0.2 mm layers, 0.4 mm nozzle, 4 perimeters, 40% gyroid infill, no supports.

- Easy-peel raft: 3 raft layers, 0.3 mm contact gap, no raft expansion.

- Orientation: print as exported. The clips print on their side, so the layer lines run around the bend and both rails come out clean.

- The plate in the timelapse (holder, both clips, and the lanyard frame that isn't released yet) took 8 h 22 min.

- The Looki outline is based on its official 50.53 x 48.02 mm size. Too tight or too loose on yours? Leave a comment saying which part.

The safety lanyard frame isn't included yet; it's coming in a later update.

v9 write-up, print timelapse and direct downloads: https://chartmann1590.github.io/homelab-the-right-way/posts/looki-l1-mount-v9/

---------- v4 (ORIGINAL, Oct 20 2026) ----------

A two-part, snap-in mount for the Looki L1 wearable camera: a cradle the Looki clicks into, plus a U-clip that slides over a hoodie collar or hood edge (about 12 mm of folded fabric). Designed in OpenSCAD; the editable .scad source is included so you can tune the fit to your own Looki and collar.

WHAT YOU GET

- looki_cradle_v4.stl: the frame the Looki snaps into. Four small ramped bumps hold the rim; the Looki drops in from the top with light pressure. Open back window for the magnetic charging pins, a round pocket for an optional magnet, a gap on the left for the buttons, and the lens opening at the top.

- looki_clip_v4.stl: the collar clip. Teeth let it slide on easily and bite when pulled up.

- looki_mount_v4.scad: the parametric source (device size, clearance, collar thickness, tilt, clip depth).

- abs_profile.ini: the PrusaSlicer profile the test prints were sliced with.

HARDWARE

- 2x M3 x 8 mm countersunk screws (ISO 10642 / DIN 7991) and 2x M3 hex nuts.

- Optional: one 8 x 1.5 mm steel disc or small neodymium magnet, glued with CA into the round pocket in the cradle floor (sits under the Looki's built-in magnet and adds pull; check it attracts before gluing).

- No screws? Set screws = false in the .scad and glue the clip to the cradle back.

PRINT SETTINGS (what the parts in the photos were printed with)

- Material: ABS, 240 C nozzle / 100 C bed, part cooling fan off.

- Layers: 0.2 mm with a 0.4 mm nozzle. No supports needed for either part.

- Raft: 3 layers, 0.2 mm contact gap, 1.5 mm expansion. No brim, no skirt. The raft is what kept these ABS parts flat on the bed.

- Cradle: 4 perimeters, 40% gyroid infill, about 2.5 h, about 13.6 g.

- Clip: 6 perimeters, 6 top/bottom layers, 100% infill, about 1 h 40 min, about 10 g.

- Orientation: print as exported. Cradle flat on its back; clip lying on its side with the U profile flat on the bed, so the layer lines run around the bend and the arm flexes instead of snapping.

- Sizes: cradle about 57.5 x 56 x 12.5 mm; clip 40 x 26 x 20 mm.

- PETG should also work (set material = "PETG" at the top of the .scad for slightly tighter pocket clearance); only ABS has been test-printed.

ASSEMBLY

1. Press the 2 nuts into the hex pockets on the inside face of the clip's front arm (the side that touches the fabric).

2. Line the clip up behind the cradle, top edges flush, U opening downward.

3. Put the screws in from inside the cradle and tighten. The heads sit flush, so the Looki lies flat on them.

USING IT

- Snap the Looki in: buttons on the open (left) side, lens at the top. Hook the right edge under the right bump, then press the left/bottom down until it clicks.

- Take it out: push on the Looki's back through the rectangular window.

- Wear: slide the clip straight down over the collar or hood edge, cradle on the outside.

ADJUSTING (edit the top of the .scad, F6, export STL)

- Too tight: clr = 1.3. Rattles: bump_ov = 1.0 or a slightly smaller dev_h.

- Collar thickness: measure the folded collar and set collar_t (10-15); squeeze = 3 makes the mouth 3 mm tighter than the fold.

- Camera aim: tilt = 5, 10 or 15 points the lens down.

- Clip depth: clip_len (default 26 mm).

More details, the print timelapse and direct downloads are on the blog: https://chartmann1590.github.io/homelab-the-right-way/posts/free-looki-camera-mount-3d-print/

Homelab the Right Way: https://www.youtube.com/@HomelabTheRightWay

Not affiliated with Looki. The Looki L1 is a product of looki.ai; this is an independent, free accessory. License: CC BY 4.0 (Charles Hartmann / Homelab the Right Way).