1 / 13
Self-Watering Cup Adapter - 2cl Shot Cup to 100ml — zdjęcie 1
1 / 13

Self-Watering Cup Adapter - 2cl Shot Cup to 100ml

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Ribbed ring that turns a 2 cl shot cup into a mini self-watering pot on a 100 ml cup. For Alocasia babies and cuttings.

Ocena
0 / 5
Polubienia
1
Pobrania
5
Wydruki
0
Wyświetlenia
55
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Standard Digital File License

🌿 Self-Watering Cup Adapter – 2 cl shot cup in a 100 ml cup

A tiny self-watering pot for Alocasia babies, cuttings and corms.

I keep a lot of my baby plants in 2 cl shot cups. This ribbed ring turns each one into a mini self-watering pot: it sits on the rim of a clear 100 ml cup and holds the 2 cl cup above a small water reservoir. Roots grow down into the water, and you can watch every one of them through the clear cups.

💧 How it works

The 2 cl cup hangs in the ring above the water. Through small holes in its bottom, or a wick, the substrate takes up water as needed and the roots grow down into the reservoir. You top up the water through the little window at the front, without lifting anything.

🍃 Features

🪴 holds a 2 cl shot cup above a 100 ml water reservoir

🫧 the small cup rests on an inner ledge with its rolled rim, 1 mm below the top edge, so it almost disappears into the ring

🎯 the base slips over the rim of the 100 ml cup and centres itself

💧 6 × 6 mm watering window at the front

👌 grip notch at the back to lift the small cup out

🌀 deep vertical ribs, like a classic fluted flower pot

👀 clear cups, so you see roots, substrate and water level at a glance

⚖ only about 7 g of filament and about 1 hour print time

🥤 Cups this fits

The fit is designed for exactly these two cups:

🥃 2 cl shot cups, JIANGZHIB, pack of 300: https://www.amazon.de/dp/B0D896TWC6 (top Ø 39 mm incl. rolled rim, bottom Ø 28 mm, height 33 mm)

🥛 100 ml cups, Gucass, pack of 100: https://www.amazon.de/dp/B0D5LTRM2Q (rim Ø 56.3 mm measured, bottom Ø 37 mm, height 65 mm)

Other cups with the same rim sizes should work too. Please measure your rims before you print a whole batch.

🌱 How to use it

1 Make a few small holes in the bottom of the 2 cl cup, or thread a wick through.

2 Fill the 100 ml cup with water up to just below the small cup.

3 Put the ring on and drop in the 2 cl cup with your plant and substrate (pon, leca or similar).

4 When the level drops, top up through the watering window.

⚠ Good to know

The print files contain only the ring. The 2 cl cups, 100 ml cups, substrate, wick and plant are not included.

🖨 Print settings

🧵 PETG (PLA works too)

📐 0.2 mm layer height, 2 walls, 15 % infill

⬆ print upright with the wide base on the bed

✅ no supports needed: 32° overhang on the slope, 45° chamfer under the ledge, short bridge over the window

🚫 please don't scale it, the fit is made for these exact cups

🎨 single colour print, no multi-colour needed

📸 About the pictures

Most images are renders of this exact model file, made in Blender, in black, clear, lilac, soft pink and sage PETG. The last three pictures are photos of a real print.

🤖 About the design

The ring was designed with AI assistance (parametric code) and tested on my own plants.

📜 License

These files are for private use only (Standard Digital File License). Not allowed: selling the digital files, sharing or re-uploading the files on other platforms, selling printed copies, any other commercial use.

💼 Commercial licenses: please contact me via Instagram @velvetleafhouse.

❤ Support

If you like the adapter, I'd be very happy about a like or a make with a photo of your print. I'd love to see which baby plants moved in!

📸 Instagram: @velvetleafhouse

🌿 Free Corm Splitting Guide and Alocasia library: https://www.velvetleafhouse.com

Also available on MakerWorld: https://makerworld.com/en/models/3361887

Happy printing! 🌿

Tagi