1 / 14
KINETA Edge-AI sports pod for the Synaptics Coralboard SL — zdjęcie 1
1 / 14

KINETA Edge-AI sports pod for the Synaptics Coralboard SL

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A battery-powered camera pod that counts your reps, measures bar speed, watches the road behind you and helps you dial i

Ocena
0 / 5
Polubienia
3
Pobrania
1
Wydruki
0
Wyświetlenia
33
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Other Ideas
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

KINETA is an edge-AI sports pod for the Synaptics Coralboard SL. It’s a battery-powered camera pod that counts your reps, measures bar speed, watches the road behind you on the bike and helps you dial in your bike fit. All the AI runs on the board itself. One pod works with a family of magnetic quick-swap mounts: barbell, rack, weight stack, seatpost, out-front bike mount and tripod.

Why it’s different

  • KinetaDock quick-swap mount: a dovetail slide plus magnets. Slide the pod on, the magnets click, and they pull the tongue tight so nothing rattles. Every mount uses the same interface.

  • MagBase: sticks to any steel surface, like rack uprights, machine frames or the top plate of a weight stack.

  • Self-contained power: one 18650 cell, USB-C charging and a power switch. The board’s own USB-C stays free for development.

  • Turbine exhaust and side gills: air flows up past the SoC like a chimney. A rain cap insert swaps in for wet rides.

  • Built for sport: TPU bumper band, recessed ports, a lens window and a lanyard lug.

  • No supports needed: every part prints without supports and fits 256 mm and 180 mm printers.

Use cases

  • Barbell (strap mount): an IMU on the Qwiic port counts reps and measures bar velocity.

  • Rack or machine (MagBase): the camera sees the whole lift, for exercise recognition and form cues.

  • Weight stack (pin clip): counts reps on any cable machine.

  • Seatpost, rear-facing (strap mount): on-device detection of approaching cars.

  • Out-front (GoPro adapter): fits any Garmin + GoPro combo mount.

  • Tripod, side view: measures bike-fit angles (knee, hip, back) and runs a flexibility screen.

The software is a concept: this release covers the hardware it was designed for.

Printed parts

  • pod_body and pod_lid in PETG

  • camera_bezel, vent_turbine and vent_raincap (optional) in PETG, in an accent colour

  • bumper_band in TPU 95A

  • Mounts: dock_magbase, dock_strap_mount, dock_pin_clip, dock_tripod and dock_gopro

All STLs are exported in print orientation.

Print settings

  • 0.2 mm layers and a 0.4 mm nozzle

  • 3 walls with 20–30 % gyroid infill; 4 walls with 40 % for the mounts

  • PETG for all rigid parts, because PLA softens in a hot car or in summer sun

  • For the TPU band: 95A, 2 walls. It’s intentionally undersized so it stays in place once stretched on.

  • You get a two-colour look without a multi-material printer: print the body and lid in one colour and the accent parts in another.

Additional hardware

  • 1 × 18650 Li-ion cell with solder tabs (3000–3500 mAh)

  • 1 × IP5306-type charger/booster module (USB-C input, 5 V 2 A output, about 30 × 21 mm)

  • 1 × SS12D00 slide switch

  • 4 × M3 × 35 countersunk screws (DIN 7991) and 4 × M3 nuts. These four screws clamp the lid, the board and the body together.

  • 4 × M2 × 4 self-tapping screws (camera)

  • 12 × 10 × 3 mm N52 magnets: 2 in the pod and 2 in each mount

  • 4 × 12 × 3 mm N52 magnets (MagBase)

  • 1 × 1/4"-20 hex nut (tripod adapter)

  • 1 × 25 mm hook-and-loop strap, 30–40 cm long (strap mount)

  • 2 × female Dupont leads and some 22–24 AWG wire

  • Optional: a Qwiic/STEMMA-QT IMU (LSM6DSOX class), an INMP441 I2S microphone, a 12 × 1 mm acrylic lens window and a 14 × 14 × 6 mm heatsink

Assembly overview

  1. Glue the magnets in place. All pod magnets face the same pole outward; all tongue magnets face the opposite pole outward.

  2. Press the M3 nuts into the hex pockets under the standoffs.

  3. Wire the cell to the module, then through the switch to GPIO pin 2 (5V0) and GND. Per the Coral datasheet, the board accepts external 5 V on that pin.

  4. Fit the module, the cell and the optional IMU into the energy layer.

  5. Remove the board’s rubber feet, connect the camera and the Qwiic lead, and set the board on its standoffs.

  6. Screw the camera under the lid, then press in the camera bezel and the vent insert.

  7. Close the lid with the 4 M3 × 35 screws and stretch on the TPU band.