1 / 6
Tote Litter Box Doorway – No-Drill Arched Entry Frame With Cut Template, Fits 1–4 mm Walls — zdjęcie 1
1 / 6

Tote Litter Box Doorway – No-Drill Arched Entry Frame With Cut Template, Fits 1–4 mm Walls

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Arched doorway for a tote litter box: trace the printed template, cut, clamp two frames on. No drilling, no flap.

Ocena
0 / 5
Polubienia
1
Pobrania
1
Wydruki
0
Wyświetlenia
16
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Pets
Licencja
Creative Commons — Attribution — Noncommercial

A finished, arched doorway for the entrance you cut into a storage-tote litter box. An inner portal sits inside the box with a collar through the cut; an outer frame goes on from outside and its sleeve slides inside that collar. Three countersunk M4 screws pull the two frames together and clamp the tote wall between them - the screws never go through the tote, so there is no drilling. A printed cut template gives you the cut line. One print fits any smooth tote wall from 1 to 4 mm.

Validation status (please read): designed and checked in CAD and in the slicer only (geometry, clearances, supports-free slicing). It has not been physically printed or tested. All pictures are renders of the CAD model with a generic stand-in tote, litter and screws - none is a photograph.

Features

  • No drilling: the three screws run from the outer frame into heat-set inserts in the inner portal (two hidden in the threshold, one behind the keystone at the top of the arch).

  • One print for walls from 1 to 4 mm: the sleeve on the outer frame telescopes inside the portal's collar, so the doorway joint stays closed by overlap at any wall thickness in that range (a uniform 0.3 mm assembly clearance, no open slot at the threshold).

  • Easy cut: tape the printed template on, trace, cut. The frames cover the cut line by 14 mm at the sides and top and 7.8 mm at the bottom, so a cut up to 2 mm outside the line stays hidden.

  • Flap-free arched opening, 168 mm wide and 169 mm tall (162 mm under the keystone).

  • Inside the box the threshold slopes about 10° toward the box and ends without a ledge - designed so litter that lands on it falls back in instead of collecting (a design intent, not a measured result).

  • Chamfered visible edges; three printed parts; no supports; every part fits a 220 mm bed.

Will it fit my tote?

  • Tote wall: 1-4 mm thick (measure it with calipers), smooth and flat over at least 206 x 209.5 mm plus a few millimetres. Ribbed or channelled walls and walls thicker than 4 mm are not supported.

  • Height: put the threshold at least 140 mm above the box floor and keep the litter bed at most 100 mm deep. With the frame size that needs a flat wall from about 115 mm to 335 mm above the floor - a tote of roughly 340 mm inside height or more.

  • Cat size: the opening suits average adult cats; very large cats may need a bigger opening (not offered).

Which files?

  • totearch_complete.3mf - ready-to-print PrusaSlicer project (2.9 or newer): the three parts on three beds, oriented, settings included. Open, slice, print.

  • PORTAL (inner portal), BEZEL (outer frame) and TEMPLATE (cut template) as STL and STEP.

  • model.py - the CadQuery source. Parameters: opening width and height, wall draft 0-10° (sets the threshold angle) and the insert hole (5.6 mm for M4 heat-set inserts, or a 3.4 mm pilot for self-tapping screws).

Print settings

  • PETG (warm rooms and a constant clamp load - not PLA); a matte finish looks best. A dark frame reads crisply on a clear tote.

  • 0.4 mm nozzle, 0.20 mm layers, no supports; 3 perimeters, 25 % / 20 % gyroid infill, the template solid (add a brim to the thin template ring if your bed adhesion is weak).

  • Orientation: inner portal with its box-side face down (the face the cat sees is the smooth first layer), outer frame front face down, template flat - as in the project.

  • 127 g of PETG; about 9.3 h on a deliberately slow generic profile (3 beds) - a fast printer needs much less.

What you also need

  • 3 x M4 brass heat-set inserts, short type, 5.7 mm long (5.6 mm hole, 7.0 mm deep) - not the long 8.1 mm type - and a soldering iron to set them.

  • 3 x M4 countersunk screws DIN 7991, stainless A2: 10 mm for walls 1-3.5 mm, 12 mm for walls 3.5-4 mm. Never use 12 mm screws on walls under 3.5 mm - they would bottom out.

  • Calipers, a fine marker, tape, a utility knife, jigsaw or hot knife, a screwdriver.

Assembly

  1. Measure the tote wall (1-4 mm) and pick the screw length.

  2. Press the three inserts into the portal slowly and flush; trim any bulge so the outer frame slides on freely, and clear any plastic pushed below the insert so the screw reaches its full depth.

  3. On the outside of the tote, mark the threshold height (at least 140 mm above the box floor). Tape the template flat with its two side notches on that height and its top notch on the centre line; trace around its smooth outer edge and bridge straight across the three small notches (they are marks, not cut line).

  4. Cut on the line or up to 2 mm outside it, and deburr. Round corners only outside the line - the collar has square bottom corners.

  5. Push the collar through the cut from inside, fit the outer frame from outside (its sleeve slides into the collar) and drive the three screws until both frames sit flat on the wall. Do not over-tighten; re-check after a week.

Use and care

Use the box with or without its lid. Clean the threshold with the litter scoop and wipe the doorway. Every few weeks, and whenever it gets soiled, unscrew the three screws and hand wash both frames in warm soapy water (liquid can creep into the 0.3 mm clearance). Check the screws now and then.

Limitations

  • Not physically printed or tested (see Validation status).

  • Smooth, flat tote walls 1-4 mm only; measure your tote - no specific tote model is claimed as compatible.

  • The joint is closed by overlap, not sealed: a 0.3 mm clearance remains. It does not keep liquid out, and it is not a crack repair.

  • Hand wash only, no dishwasher. Keep spare screws and inserts away from pets.

Pictures

All pictures are renders of the CAD model, not photographs: the doorway on a clear storage-tote litter box (cover and a front view), a section through the joint, the exploded assembly, the dimensions and the assembled frames on their own. The tote, litter and hardware are generic stand-ins.

Tagi